Jump to content
SAU Community

Recommended Posts

Are -10's the Garrett GT2871R Ball Bearing Turbos. You guys hav much info about the -10 in terms of when they come on boost, top end power etc? Do many gtrs hav this setup?

Cheers

Unless its on a 3L + I wouldnt go near them. I have RS's (pretty much -10's) on a 2.8 and they will be replaced with a set of -5's. Stupid choof choof turbo's

whats up with the last RB26 dyno post -5's @ 18psi and only 270rwkw ?? sure its pretty much a standard engine, but I had standard engine & standard turbos high flowed making exactly the same power at the same boost ??

theres quite a few others on there @18-19psi making around the 360rwkw mark ? doesn't look right

yeah stock turbos will make 270kw with some cam gear adjustment, 15psi and a good tune (my old car did and still does). still different cars get different results. no way to know what the tune is like, or the supporting mods etc or even how accurate the dyno is. at say 20psi I've seen -5s make between 300kw and 360kw. the mid point of around 330kw is about what they should make at that boost. anything more is gravy. :)

whats up with the last RB26 dyno post -5's @ 18psi and only 270rwkw ?? sure its pretty much a standard engine, but I had standard engine & standard turbos high flowed making exactly the same power at the same boost ??

theres quite a few others on there @18-19psi making around the 360rwkw mark ? doesn't look right

Wouldn't be surprised if they're -9's with a result like that

im glad i got -7's, they are so dam responsive, perfect for a quick street GTR...

my goal was to run around 280 - 300kw with the stock internals, but with sard fuel pump, nismo 600cc injectors, r34 gtr dumps/stainless front pipe/de-cat/3.5" cat back zorst, nistune, greddy cam gears, greddy profec b spec 2

so far only been road tuned on 18psi without cam gears dialed in, getting dyno tuned on the 12th of this month, hopinh for a solid number and a punchy mid range @ 20psi and gears dialed in

will post results in few weeks time :)

  • 4 months later...

read through this whole thread and -9 > -7 from what i can see, also would a gtx3582r with .82 rear be compairable response to a pair of -5's? obviously be light switch power with the 35 but i was wondering if they would come on in a similar rpm.

  • 2 weeks later...
  • 2 weeks later...

I know time and time again people say just to buy garrets, HKS isn't worth the mark up.

BUT

would a GT-SS set up have ANY benefit, no matter how small, over a -9 set up ??

Also from my understanding, HKS kit comes with everything you need to install and the -9s are turbos only, would the cost be more comparable after you buy the rest of the necessary items to fit the -9s ?

thanks for any replies :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hell, I'm sufficiently wary of the ZSS suspension arms, let alone something like a hub.
    • Got it back home and got started pulling the hub off and diagnose the issue. Axle was stuck after removing the 36mm nut so i used a 3 jaw puller to try and push it out and... eH5FXvJ8.mp4   spend the next few hours trying to remove the axle from the remaining hub as it was very much jammed in there when the spindle sheared off. resulting damage as below R53AIy6 - Imgur.mp4   Looks like the was already a stress fracturing in the spindle as can be seen with the darker cracked section My working theory is maybe when the pinion gear exploded last year the shock put through the hub was the initial crack. Then a few events later it finally let go. Just lucky it happened where it did and not 190km/h on the next sweeper or into the hairpin The bearing/hub assembly went in in 2019 and were non-genuine "ZSS" assemblies and no nails were harmed in the process. #BreakHubsNotNails
    • Thanks mate, couldn't find in VIC, ended up ordering one from NSW, getting rwc to get new plates and registration done.
    • Before all the EFR fan boys come in, have a look at: https://www.garrettmotion.com/racing-and-performance/performance-catalog/turbo/g-series-ii-g30-825-58mm/ It also comes in a T4 1.06 divided housing. I would dare say if you want response & also decent power, this thing would chop.   AND apologies, just re-read your post, you've already bought the turbo... whatever you do, make sure you stick with divided housing and proper twin scroll manifold.
    • People have got to stop doing that. ShatGPT is not a search engine. It is a hallucination factory.   I also would recommend the 1.05. The .83 will "work" for you , in that it will be more responsive, but I think you'll find that it won't be anywhere near as good running it out to 8000rpm as the big housing will be.
×
×
  • Create New...