Jump to content
SAU Community

Recommended Posts

heya installing the Sard 550's into my rb25det motor. purchased through justjap, theyre brand new. what seems to be the problem i that the new injectors are:

1- not as wide as the original ones, therefore slide in and out of the rail very easily

2- both top and bottom O-rings dont seem to be sealing up

3- the injector cap (the cap thing that holds the injectors in) dont fit back on if i sit the injector into the rail

am i doing something wrong? am i meant to change the O-rings or anything? is it possible the injectors given to me were wrong? bear in mind the RB25's are sidefeed injectors.

all help is much appreciated!

Link to comment
https://www.sau.com.au/forums/topic/256477-installing-sard-550s-o-rb25det/
Share on other sites

You have to use std RB25DET injector o-rings from nissan. The sards do not come with the correct o-rings.

Good luck mate. If you are not sure make sure you get some one with a mechanical background to check you as side feeds can be very tricky.

well test fitted the standard O-ring that was on my stock injector and its very loose with about a 1-2mm gap between the injector and the O-ring. ..any alternatives to the Nissan ones? car goes in on friday morning for the tune! ugggg

ok removed the rubber bits in the caps and fit looks ok. still need to seal off the upper region .....somehow......so new standard O-rings?

No need those are just dampers for the std injectors.

thanks for the confirmation URAS.

fark new O-rings are a rip from nissan...$5 each x 6....

injectors are in the rails now, fit is good, though not sure how tight to screw the allen key bolts down. are the collars meant to touch the rail? currently mine are 2-3mm's away from touching but theyre pretty damn tight already, sounds right?

  • 6 months later...
thanks for the confirmation URAS.

fark new O-rings are a rip from nissan...$5 each x 6....

injectors are in the rails now, fit is good, though not sure how tight to screw the allen key bolts down. are the collars meant to touch the rail? currently mine are 2-3mm's away from touching but theyre pretty damn tight already, sounds right?

Yer my collars didnt clip on properly, touching the rail.. not sure if this is bad or not though.

Anyone have any info on this?

Sard sell an optional part which is a seperate collar that's required for some cars when using their injectors. You may need a set of those.

http://www.nengun.com/sard/injector-collar

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • 310mm rotors will be avilable from Australia, Japan, and probably a few other places. Nothing for the front can be put on the back.
    • The filter only filters down to a specific size. Add to that, the filter is AFTER the pump. So it means everything starts breaking your pump even if its being filtered out.
    • Just like in being 14mm too small (296mm) makes it not fit, being 14mm too big (324mm) it also won't fit. You want to find the correct rotor.
    • @GTSBoy Ok so that was the shops problem...they showed R33 rotors on R34 page and i did not know 296 do not fit(and are for R33) Yes i bought "kit" with rotors and pads. Pads are ok(i have GTT calipers front and rear). They have some 324mm but no 310mm. So i dont know if they would fit. I have 17inch LMGT4s So another question. Can i fit those in the rear or they are just "too" big for that?
    • I started removing the tank a while back with the intent to give it a proper clean. Got to a bolt that I couldn't undo completely due to a diff being in the way, so just said f**k it and siphoned the gluggy old fuel out and called it a day. Looking it the tank it looks less corroded than the one in the pics for that billet hanger from Frenchy's anyway. Isn't it the fuel filters job to worry about this stuff? I scraped off most the crusty shit of the hanger but will give it another go before reinstall coz maybe the fuel and return pipes are also full of gunk  
×
×
  • Create New...