Jump to content
SAU Community

Recommended Posts

Just dropped in a 68k Rb26 with HKS 2510 turbos into my 32 gtr. She started up really easy idled really really rough and blew alot of white smoke. This finally cleared so i guess it was just oil from the engine sitting around for a long time.

Heres the current problem. It is really really slow to free rev takes ages to get to even 4k. Stabbing the throttle does stuff all compaired to my old rb20.

Taking it for a test drive tomorrow to see how it goes.

Now I know there is one problem the CAS was loose. We have set the timing to where it idles the best and tightened it up. Want to get a timing light on it but cant see how with the coil plugs.

Any ideas on setting timing and the possable problem?

Link to comment
https://www.sau.com.au/forums/topic/256730-new-26-just-dropped-in/
Share on other sites

you can still use a timing light to find the base timing id say its either CAS or maybe the timing belt now put on properly possible skipped tooth?

Where do you hook the timing light up too? i doubt its skipped a tooth on the timing as belt is well tensioned and was not removed being a 68k engine it should be due for replacement yet.

Taking ages to spin up is probably due to timing too retarded, so that maximum combustion pressure occurs after TDC. Using a timing light on RB-series engines has been covered numerous times.

Did you get the injectors cleaned before you installed the engine.

... Running some injector cleaner through it with the fuel. ...
Pretty much a waste of time, if the injectors are already dirty. And if the engine has been sitting around for a while, who knows what condition they are in?
Where do you hook the timing light up too? i doubt its skipped a tooth on the timing as belt is well tensioned and was not removed being a 68k engine it should be due for replacement yet.

Run a HT (conventional coil lead) lead between the coil pack and spark plug and clip the timing light on that.

Timing gun attached and working. Just need to be 100% sure about setting the timing.

Idle at 950rppm timing should be set to 20deg BTDC

From left to right what does each mark represent? I think i have it done right but just want to make sure.

Have searched through the gtr service manual but at 300 pages i haven't found anything yet.

Cheers for the help

left to right what does each mark represent? I think i have it done right but just want to make sure.

Have searched through the gtr service manual but at 300 pages i haven't found anything yet.

Details are shown on page EN-11 of the genuine service manual......28 pages in from the start of the manual (well, it is in my electronic version)

Don't know how I missed that part. OK Timing set now. Issue with coil pack fixed and she now seams to be running alot better.

Al tho its now blowing a heap of white smoke when i give it a bit of throttle. Smells like oil burning. Could it be oil in the cooler pipes from the old engine?

  • 1 year later...

May as well update this even tho car is gone.

White smoke was from a massive build up of oil in the cooler pipes from the old engine.

Engine problem was due to dodgy silicon joiner that would only open up under boost. Car ran perfect after this.

Edited by Crans
  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
    • Agreed, and in particular the earth strap that should go from the subframe to the chassis but it often broken or left off. There is a section in the R32 workshop manual you can follow for troubleshooting if you don't see anything suspicious, and depending where you are (there is no location on your user profile) you should be able to get your hands on a second hand replacement unit still if needed
    • Yeah they mention as a R34 for 2.5 Turbo...but then again thos "small" were also for R34 by that different site. But i look into it and that 310mm EBC is for R34 GTT. And by those you linked the specs are the same 🙂    EDIT: I found these on one site here: DBA 4000 series T3 DBA42304S They are 310mm...and it says are for R34GTT...are there good? EDIT2: ok they have pads too.  What "color" should i get for street use? I dont want/need some noisy ones...(and if they are not that dusty that is good too)
    • Yeah, shame. Maybe  driver's carpet is available 🙏. I am waiting for both amayama and nangun to confirm.
×
×
  • Create New...