Jump to content
SAU Community

Recommended Posts

  • Replies 2k
  • Created
  • Last Reply

Top Posters In This Topic

']wats the max power u can get from a stock turbo FJ? just curious.

and also wat management systems are you guys running? do u have seperate coils rather than sticking with dizzy n shit? (on FJ20s if ne1 has em!)

wolf 3D are good for the fj, they could also be able to provide a simple plug in and play system for you now, $1500+ tuning..

has anyone found info on r30s on any other forums?

There was some discussion on Skylines Downunder until the KIWI's got all funny.

Probably because it is their forum, but were out numbered by aussies, on all forum topics excluding NZ.

But absolutely nothing like this thread.

And there was a Nissan Skyline - Paul Newman sales publication on ebay the other day, that I think I beat crimmo to. By the sounds of the advert, it may have some interesting info in it that I will post.

Things like "wind tunnel tests" etc, on all 1983 > R30 models including DR's & HR2000GT ES & 4 dr's & Hatch 2000GT E etc.

1.  Mobil 75W/90 full synthetic is the oil. It performs as well as Royal Purple, Penrite, Castrol etc and is readily available for top up when necessary.

2.  My R200 4.1:1 is a mechanical CUSCO centre LSD with 80 odd lb preload and I have a Nissan 3.9:1 as a spare.

3.  No! the car is not on the road at present, but as soon as it is I'm heading your way sort of, got to see a mate on The Gold Coast.

1.Sounds good.

2.Good to know,as I'm sure the R32> R200's with the viscous lsd wouldn't need the same spec oil as the early mech R200's.I've ben wanting to confirm a good mech lsd oil with someone who actually has one,not a sales person who thinks an HR31 coupe is a fancy Pintara.

3.Any estimates on when it will be? You'll have to stop over in Port Macquarie on your way...you know,stop,revive,survive.....and so I can check out the '30! :cheers:

']wats the max power u can get from a stock turbo FJ? just curious.

and also wat management systems are you guys running? do u have seperate coils rather than sticking with dizzy n shit? (on FJ20s if ne1 has em!)

I had an EMS QI-4 fuel and ignition ecu running mine.Used the stock FJ dizzy.The EMS was good,could work with several factory pick-up systems.

I'd like to go multi-coil in the future though...

Only problem with the wolf that i know of with the FJ dizzy is u have to get it modified...Bit of hassle for someone like me in SA where if i get defected then i have to try to find a standard FJ dizzy...I am considering going for the EMS 8860 seems like a good piece of equiopment!!

Ghostrider i beleive that u might've beaten Crimmo to that, i was talkin to him last week and he was telling me about that book seems like its quite a handy piece of gear to aquire!!

Yeah the 8860 sound as good as a Motec on paper,and you couldn't complain at $1600.....

If you try getting in touch with EFI Hardware www.efihardware.com they have a programmable ECU (HAWK) and has been working on plug & play systems.

The Hawk has had some pretty good reviews from Zoom when they last did a comparison.

Cost is only $1300.00 or there abouts, but don't know if anyone does them in Adelaide. They seem to be Haltec mad in Adelaide.

Wolf do the V4 Plug & Play ECU which is $1395 for the ECU itself then install and tuning take it to around $2200 ready to drive away. but then i think u have the cost of the multi coil setup added to that so it could get pretty expensive :D

but todd off these forums with white dr30 here in perth is happy with his he is running Wolf V4 with multi coils and making 360 odd rwhp quite happily!

i was hoping for a cheaper sortof alternative like microtech or something is all. wondering if anyone has gone that way. i only earn 200 a week doing nightfill so was hopin there mite be a cheaper one that'd do the trick! that EMS 8860 i guess is $1600 just for the ECU, then tuning install etc would run it out a few hundreed more expensive that the Wolf V4 p&p i guess.

ah well i dont have 2k+ for an ECU atm neway, but i guess it seems Wolf V4 is gona be the way to go in the end :) :) better hope santa brings me a big wad of cash this year haha

Yeah the 8860 sound as good as a Motec on paper,and you couldn't complain at $1600.....

Yeah thats what i rekon to!! My mate is currently having it setup on his series 4 and its a pretty wild motor in there so once thats all done then i shall decide, but so far im impressed with it all! :aroused:

Ghostrider : not everyone in adelaide is haltech mad, but the majority of people here are..If not then like PFC al depends on who u go to really, so many people deal with the same ecu's so its not like deepnds on the workshop u goto depends what ecu u use cause most of them will use 99% of ecu's available

.75 degrees sideways, just bought a r31 with an rb20det in it running a older wolf3D, version 3 i think, the bloke who had it before didn't know that there is a locking system that requires a pin number to start the car if active. my mate went to change the pin and the car wont start!!! had to sent the computer to sydney to get it changed to the new pin so it will work...poor bastart had the car for 24 hours then its been sitting there for the last 48 unable to be driven!

oh my mate ran a microtech DIGI 1 (or was that 2??) on his FJ20.

you can pickup alot of stuff second had cheap and on ebay and stuff, i know a few guys that have been doing so recently.

what ecu's out there are able to run in closed loop? i know my microtech doesn't :(

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Welcome to Skyline ownership. Yes, it is entirely possible parts websites get things wrong. There's a whole world of inaccuracies out there when it comes to R34 stuff (and probably 33 and 32). Lots of things that are 'just bolt on, entirely interchangable' aren't. Even between S1 and S2 R34's. Yes they have a GTT item supposedly being 296mm. This is incorrect. I would call whoever you got them from and return them and let them know the GTT actually uses 310mm rotors. Depending on where you got them from your experience and success will obviously vary.
    • Hi...a bit a "development" on the brakes. I spoke to the guys where i get brakes from...and they are saying that 296mm EBC are for R34 GT-T. I then went to their site: https://www.ebcbrakes.com/vehicle/uk-row/NISSAN/Skyline (R34)/ and search for my car(R34 GT 1998 - it has GTT brakes) and it show me this USR1229 number and they are rly 296mm rotors... So now iam rly confused... The rotors i have now on the car are 310mm asi shown... So where is the problem? Does the whole EBC got it wrong or my calipers are just...idk know what?  
    • Oh What the hell, I used to get a "are you sure you want to reply, this thread is XX months old" message. Maybe a software update remove that. My bad.
    • This is a recipe for disaster* Note: Disaster is relative. The thing that often gets lost in threads like this is what is considered acceptable poke and compromise between what one person considers 'good' looks and what someone else does. The quoted specs would sit absurdly outside the guards with the spacers mentioned and need  REALLY thin tyres and a LOT of camber AND rolling the guards to fit. Some people love this. Some people consider this a ruined car. One thing is for certain though, rolling the guards is pretty much mandatory for any 'good' fitment (of either variety). It is often the difference between any fitment remotely close to the guards. "Not to mention the rears were like a mm from hitting the coilovers." I have a question though - This spec is VERY close to what I was planning to buy relative to the inboard suspension - I have an offset measuring tool on the way to confirm it. When you say "like a mm" do you mean literally 1mm? Or 2mm? Cause that's enough clearance for me in the rear :p I actually found the more limiting factor ISNT the coilover but the actual suspension arms. Did you take a look at how close those were?
    • @GTSBoy yeah sorry i know thery are known for colors bud those DBA are too in colors 🙂 Green will be good enough for me  
×
×
  • Create New...