Jump to content
SAU Community

Recommended Posts

boost is not related to stock coils keeping up or not

they simply die of old age

so you can run 27psi if you like

one day they will die and misfire regardless of engine boost

once the engine is on load, it will misfire

so run whatever you like

1.3kgcm2 if you want

the turbo is a high flow, the ecu is std but has a haltch intercepter connected which has been tuned, The engine has forged pistons. Im guessing the coils are as old as the car. Someone told me it could be the higher boost is blowing out the spark?

breaking down spark is different to coils dying

coils die due to age, when they die, like i said, they misfire as soon as the engine is on load

ie one day its fine, next misfire city, so its all of a sudden.

spark breaking down is usually too much boost or wrong gap or intake temp too high

or combination of all three usually. if running less boost cures the misfire its probably spark breaking down

my coils lasted 160,000 then gave up

coils die due to age, when they die, like i said, they misfire as soon as the engine is on load

ie one day its fine, next misfire city, so its all of a sudden.

In my experience the typical coil misfire is the insulation giving out, everyone I know who has put work into decently re-insulating them have fixed it fine. I run up to 18psi on my original S2 R33 coils with extra insulation on them is going fine :(

Yea it happened really bad one night when the air was still pretty hot. I found a few FAQ's on how to insulate the coils, So i might give that a go and replace the spark plugs. What better out of BCPR6E or BCPR7E? Or do people recommend any other ones?

who can repair coils?

I have splitfires in mine atm, sometimes when I leave car to warm up in morning, it will run on 5 cylinders, ill go out, disconnect connection to coil #3, plug it back in and away it goes back on 6 cylinders.

But when I drive and give it a little stick, it starts miss-firing so i assume its that faulty coil?

who can repair coils?

I have splitfires in mine atm, sometimes when I leave car to warm up in morning, it will run on 5 cylinders, ill go out, disconnect connection to coil #3, plug it back in and away it goes back on 6 cylinders.

But when I drive and give it a little stick, it starts miss-firing so i assume its that faulty coil?

the 10+ year old plug or wiring is likely at fault vs a new ~ish splitfire coilpack set

You can also get the coil pack loom from Nissan for around $140AUD from memory... its pretty cheap if the plugs are a bit stuffed.

I purchased new for mine with the splitfires, good insurance.

And for the record i made 370rwkw on stock RB25 coils, they were in very good condition :D

You can also get the coil pack loom from Nissan for around $140AUD from memory... its pretty cheap if the plugs are a bit stuffed.

I purchased new for mine with the splitfires, good insurance.

And for the record i made 370rwkw on stock RB25 coils, they were in very good condition :D

yeah...quite a high price..it might be better to find a private seller they might charge 30 bucks or lower.

A private seller for a coil harness?

I paid $120 for mine from RHDJapan, with shipping it worked out to the same as getting it from Nissan but got it in one week instead of three. I looked up the harness on RHDJapan recently and they're up around AU$270 delivered now :)

I was troubleshooting a misfire when hot issue for AGES, turned out it was the insides of the coil harness plugs falling apart.

yeah...quite a high price..it might be better to find a private seller they might charge 30 bucks or lower.

I meant quite low price considering…

Why get one 2nd hand for $30 only to have the same damn problem 6 months later?

Makes zero logical sense. You cant get them much cheaper as bubba has pointed out :)

Pay the Nissan price, its actually reasonable in price for something OEM and after 10-15 years does need replacing

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • If you have the original log book and it didn't have a chassis number quoted, then no money required.  I have "rechassied" a number of race cars, no problem as long as you have the original log book.   Cheers Gary
    • Well the good news is that it won't run any worse with an atmo bov than it does with no bov, I've owned a few Nissans over the years (r32, s15 and now r33), the stalling issue caused by a bov or no bov while still having an afm is easy enough to live with, most people get used to driving them and just feathering the throttle when you come to a stop to avoid it stalling. Changing to a proper ecu with a map sensor is ideal but in the short term I'd just slap in the bov if you really want the whoosh sound. I looked into the pass through type maf like the R35 one above but decided against it as the amount of oil and crap flowing through the hot side would mean you'd have to clean it often to keep it working.
    • Build an 800hp motor. Make it as bullet proof as you want, you WILL still break things. Like, the rest of the car. Heck, even as a dead stock car, things will still break, but the more power, the more everything else will let go easier. From gearbox gear sets, to extra stress on the chassis/mounts, more stress on diff, axles, tailshaft, even the suspension mounts. Check out the motorsport build that last year went to a Bosch motor sport ABS setup, and now can brake so damn hard it's twisting mounts for suspension/subframe etc. Now if the brakes can do it, imagine what happens with super grippy tyres and 800hp in a low gear...   Shit, I'm presently out fixing the girlfriends daily driver that rarely sees past 3,000rpm and is used to cart the dogs around in. Everything WILL break. If you don't want it to break, don't drive it. And then laugh, as it will still break without even being driven!
    • ECUMaster is an Australian company from memory, been around a while, and seem to actually play really well on more unique engine setups. Seems to be more of them being used in the states, and they seem to support more cylinders than most others.   My opinion on stock ECU/Nistune with he AFM, is you can tune around the issue of stalling. It's still a bit of a band-aid, and not the most perfect smoothest setup, but it can make it drive able and not an absolute PITA. But you're still compromising. A vent to atmosphere BOV has the same issue as no BOV with regards to the AFM. Both make the ECU think more air is entering the engine than there really is. And I can't find any hard science/decent evidence that supports the claims all the "you MUST run a BOV of some sort of you'll blow the turbo up". About the only one some people can give of why is "lag between gear shifts", and that is only an issue when your boost source for the waste gate is pre throttle body. I ran my boost source for the TD07S off the inlet manifold. Didn't have weird boost spiking issues, didn't have boost control issues, and on a gear shift the wastegate slammed shut, which meant all exhaust gases would be keeping it going round and round and not waiting for the wastegate to shut again when I stepped off the clutch and back on the loud pedal. It came back on boost in the next gear pretty much instantly.   ECU / tune / BOV choice I think really comes down to a lot more factors than just what you've stated. And personally, especially for daily driving, recirc setup for the BOV, or no BOV. I dislike the really loud BOV when everyone is taking off from the lights etc.
×
×
  • Create New...