Jump to content
SAU Community

Another Stolen Skyline

MANG

By MANG,
in Australian Capital Territory

 Share

Recommended Posts

  • Replies 71
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Sinista32 Grand Master

Sinista32

Posted
Posted
ive been told 3 stolen skylines have been spotted near griffith flats! go check it out!

Amazing intel Rev Head!

The White 33 at the top of this thread is there. Couldnt see any others in the Stewart/Griffith flats. This car has had the wheels changed over although there is a stock wheel or two next to this vehicle. Plates and rego sticker removed. P plate still in place which confirmed right car.

Thanks for your help Snooze identify this as the car :).

Sinista32 Grand Master

Sinista32

Posted
Posted (edited)
So what happened?? Did you wait for the cops Sin??

You already know my opinion in relation to Cops plus I took protection with me. Placed the call, hung around for a 20. When i called I was advised that they will attend when a unit becomes available. Manuka across from BP, expected timeframe greater than I could wait.

I have to bury a close mate in Victoria so I'm leaving early 2moro so I left the area.

Car Location:

Evans Crescent Griffith. Block 7 unit 1 to 21. Turn first left at the big lights past Kingo Pub when your heading down canb Ave towards Maunka, left again and second set of units on the left. Right halfway down the driveway!

Edited by Sinista32
Sinista32 Grand Master

Sinista32

Posted
Posted

Car Location:

Evans Crescent Griffith. Block 7 unit 1 to 21. Turn first left at the big lights past Kingo Pub when your heading down canb Ave towards Maunka, left again and second set of units on the left. Right halfway down the driveway!

555kkk Experienced

555kkk

Posted
Posted
The drug f**ked feinds who are gutless bitch assed theif/s definately scan this forum. BEWARE!!!

This Skyline has been moved since being spotted and posted. Realy sorry folks, my fault.

maybe you could talk to mods and find out who looked at this thread yesturday ?

have you got a picture of car put it up on the site some where with cash reward ??

Bullet32 Veteran

Bullet32

Posted
Posted
The drug f**ked feinds who are gutless bitch assed theif/s definately scan this forum. BEWARE!!!

This Skyline has been moved since being spotted and posted. Realy sorry folks, my fault.

Not your fault Richard, I would blame the lazy ass cops who couldnt be f_cked sending one unit to check it out while you were there... :banana:

Last time I checked car theft is supposedly a serious crime.

JD_R33 Proficient

JD_R33

Posted
Posted

Cops did show last night, not sure what time though. I got called into work and they were still there when I drove by on the way home.

They were there again this morning in numbers. Has anyone heard if any of the cars turned up yet?

There are a sh1tload of people living in that complex, someone must have seen the cars and know which "residents" were working on them.

Rev_head88 Enthusiast

Rev_head88

Posted
Posted

if i hear anymore ill keep u guys informed

i know alot of poweful people in canberra..

when i get my new skyline if i see someone even close to it that i dont know shits gunna really hit the fan

eyes are still peeled these f**ks should be jailed far far away

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      (it is a brand new ported mellings pump) I suspect the lack of pressure is due to the leak. It was *not* that low in other logs of oil pressure in the past. It wasn't that hot either, but not far off.
    • The Bogan
      Mistakes were made, my R34 Story

      By The Bogan · Posted

      Would a Mellings oil pump be a viable option  From my time with a LS, and talking to tuners and LS specialists, the "weak" OEM oil pump is one of the first things they recommend to swap out if I was going to give the engine any high RPM I opted for a Mellings high volume, with the high pressure springs and I never had a issue with it Cost wise they are not expensive in the scheme of things 
    • davemoto63
      My new to me M35 Stagea wagon

      By davemoto63 · Posted

    • davemoto63
      My new to me M35 Stagea wagon

      By davemoto63 · Posted

      Just bought a 2002 Stagea 250tRS VR-X Four AERO VQ25DET and spent the last two weekends cleaning and detailing it.. still have to do the wheels and the engine bay but the rest of it came up nice. Imported 2011 to S.A. and I'm the third owner since it was imported. I met the guy who brought it over, he went to Japan and picked out the car, bought it and ordered the wheels. He also gave me a list of stuff he did to the car with receipts. Coil overs (I have the original springs), 3" exhaust from the dump pipe back no cat, Custom dump pipe,(I have the original exhaust), Plenum spacer, 18" custom Work XSA wheels (need restoring, I've made a start..), Shift kit put through the 5 speed tiptronic auto, TV and menus/screens changed to english, Australian DTV tuner installed in rear. I've just had four new discs and new pads as well as all the fluids including the brake fluid replaced. I have all the receipts for the last 15 years and the import papers in a nice folder. Car looks great, goes like hell but fuel economy is not a thing lol.. pics next..
    • silviaz
      Steps to DIY sanding car back ready for respray....

      By silviaz · Posted

      I ended up in this rut again lol, and used a shit ton of filler. One thing I can't understand is, even after using a big long block and going in long X pattern strokes, I always end up at bare metal again with no filler, and my repair started at one end of the door and now I've chased my tail to almost the other end of the door. I was thinking of hitting the panel with a hammer where it might be a high spot and making everything low then filling it, I did this on a small section on my other door by mistake and I think I fixed it lol. Is this a bad idea? The other thing is with guidecoat, whether it's the powder or spray, after I sand all the guide coat off, it doesn't reveal anything for me in terms of high spots and low spots and makes it especially hard when it's bare metal (at least in powdered form), am I doing something wrong here, or likely a high spot I keep going over and creating valleys? Lastly, stupid question but, is it possible that after sanding if I only sand over the filler area where I know to be a dent that it's impossible for me to dig into that dent? Unless there are other problems which I missed.  
×
×
  • Create New...