Jump to content
SAU Community

Recommended Posts

Hey all

Got and installed my new intake on the V35.

I also put a new K&N panel filter in. Its the same model number as a VS 3.8 litre commadore. A360.

It looks pretty good to me, i might use a longer piece of silicon pipe for the end nearest the box, but just to neaten it up a bit.

The sound is way better in the higher ranges and when the throttle is nice and wide open.

Down low, its great, no more noise than stock until you give it a hit.

Photos attached and a video with a digital camera.

The sound quality isnt great, but you'll get the idea i hope.

IMGP4553.jpg

IMGP4556.jpg

IMGP4558.jpg

(I dont know how to add the video to the thread)

Edited by V35 Matt
Link to comment
https://www.sau.com.au/forums/topic/259921-new-intake-on-the-v35/
Share on other sites

  • Replies 94
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

got the pipe off ebay. No idea what brand it is, but i like the stainless look rather than the plastic look of the z pipe.

Self install with a mechanic mate. But having seen it installed, anyone could do it without any worries at all.

Took 15 mins, as we removed some of the excess plastic from the box and the intake.

Now the muffler to install and it'll be complete as far as external mods go.

Hope to get better video over the weekend of the engine and the sound of the car going past.

wanna ask for some suggestion.. i heard somewhere that the oem 350z intake pipe is actually better, compared to stainless steel pipe, due to reason that stainless-steel pipe gets hotter easier and faster than plastic, so actually hot air are being suxked in..

Anyone can help to explain if this is right or wrong in anyway?

I do kinda agree if someone told me plastic gets hot the same way just like stainless steel... but it does also get colder faster than plastic rite?

this is the reason i still cant decide wat kind of intake i should buy and install on my v35.. ;)

The Truth from 350z is that the Intake is already a great design on 350z, They just need to use a Drop panel filter and it's already Perfect. But if you want the Noise you can go for the POD (ie JWT pop Charger). also most of the tuner in japan uses the SS tube like Matt did. So about the heatsoak i'm not too sure, if you want can just heatwrap it or so.

myself uses the CF Tube on mine with the K&N Drop in Filter.

P1000129.jpg

to be honest if you want to get the Z tube. at least get the one from US version. It doesn't have that Water Collector/Resonator on the tube like the Australia version does.

Cheers

Is that what it is!?? I asked the question on the g35 forum a while ago and no one could tell me exactly what it was or how come theirs didn't have it. Oh well...still does the job I guess.

Is that what it is!?? I asked the question on the g35 forum a while ago and no one could tell me exactly what it was or how come theirs didn't have it. Oh well...still does the job I guess.

Yeah, that stupid appendix thing is a resonator. The US models didn't get it. I am pretty sure the Japanese cars did. It's for NVH.

Honestly, if you bought a 350Z you shouldn't be allergic to a bit of induction noise.

Yeah the stainless steel pipe does get a bit warm but I think it would be hard to notice a difference in power compared to say a CF one, would probably only show up on a dyno over a number of runs. I should probably feel how warm mine gets now since I put the Kinetix Plenum on, would help a bit I imagine as that isn't metal.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...