Jump to content
SAU Community

Recommended Posts

huh? that's wierd, if boost increased when you made an exhaust change, wouldnt this indicate more of a restriction?

that is, the backpressure can't escape quick enough, which drives the exhaust wheel faster, which drives the compressor wheel faster, which increases boost in the intake side without any change

Other way around.

  • Replies 40
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

i've got a full exhaust on my GTR

Mines Dump Pipes

aftermarket front pipe (Stainless)

hi flow cat(stainless)

3in stainless cat back with oval muffler

the dump pipes arent needed, i only did mine cos i changed the turbos, and though "may as well"

just get a aftermarket brand front pipe, good hi flow cat and ring around a few exhaust shops and get them to do a cat back.

i didnt really worry about which brand to use, its all just metal, and just as long as its all mendrel bent youre fine.

and when it comes to sound if youre that picky, try and find a muffler that will give you the note you want, and if you need you can always chuck a hotdog in to deepen the note if need be.

good luck mate,

i'm sure youre gonna like what you get, i know i love the sound of my exhaust!

Brezza

At the moment im running Tomei manifolds, HKS dumps, HKS front pipes 3.5 inch cat and a Kakimoto Full mega N1. Pretty damn quiet at the lights and driving.. NO drone what so ever. On boost... My god what a noise!!! I couldnt believe how much difference the cat back has made. I had some 3 inch "cut and shut" system on their before.... Just with the catback change i reckon its going better on 1.3 bar with timing pulled out of it then it was on 1.7 (2.8 stroker twin GT RS's). However it wont be cheap as previously said :P

Hey guys, on this subject, I have a GTR with a pair of 2860's, with CES split dumps to Y-pipe to 3.5" hi-flow metal cat. Basically my old exhaust (unknown brand, 3") was reflanged to fit the cat.. What would you guys suggest I get? I'm past my "run in" stage on my new motor, so I need to get my final tune done.

Thanks for your suggestions! :D

Kakimoto Regu 06+R or the Full mega N1

Paul

Man your idea of not loud must be way different to mine or some how the top part of my system must do some nasty damage. I have the Full Mega N1 (single pipe not twin) and without the additional baffle pipe in the cannon (inner silencer) it is a cop magnet - loud and on boost I agree awesome but really loud. Top part is a custom 3" bell mouths off turbs to 3.5" collector to 4" metalcat to N1.

Cheers

^^

Well when i bought the system i was pretty worried about how loud it was going to be at idle and say sub 3500 RPM. Started the car and it just purs. Ive had a mate drive next to me and he said he can hardly hear anything. On boost it absolutely SCREAMS but without big revs adnd the gates not open its quiet as.

  • 4 weeks later...

Hi, know nothing about exhausts. Am going to look at one tomorrow.. XForce apparently 3" to cat (xforce cat?) and 4" rest of the way + full stainless. Its at a good price so I'm pretty much sold on it unless someone can tell me different? (To suit GTR33)

Also, is it going to loud as hell?

Cheers guys.

Edited by Ten Four
Can someone confirm before I go and buy it please...?

4" from cat back will be pretty loud, I have a Trust Power Evolution 2 (94mm but close enough to 4") and it is pretty loud, you will get defected.

Depends if it is 4" with a few decent mufflers in there to be under the dB limit?

Cheers, dont have much info atm, just what i said above. I'd be going to buy it today but haven't got a ute atm... Getting it tomorrow in a hatchback :rofl2:

I would find out a bit more info before you commit and hand over cash!

380kw has been made on stock 33 GTR dumps with 2560 turbos.

Im changing back to standard GTR dumps because my stainless HKS split dumps are giving me creep. Also running 2560s.

Im also running a HKS Dual Racing Exhaust, its a full twin which never joins. Tuned length dual.

By changing from a single 3.7 HKS Super Dragger to this exhaust, boost shot up to 23psi from 17psi with no other changes! Let me say it must flow very well!!!

I have R33 GTR Dumps for sale if you need them, the R32 ones are crap.

P.S CES have the worst customer service in the world! dont bother with them!

Was the twin system much/any louder than the single?

I am looking at changing from single to twin system possibly.

I would find out a bit more info before you commit and hand over cash!

It's also apparently 2 months old. I'm mainly going for it cause its only $250 and its all xforce. I had thought 3.5" was the max one should run. Will 4" be unbearably loud cause this is a daily driver...

I rekon twin systems are the bees knees. if you have one direct exhaust path for each turbo it will not only help flow issues but it gives you more room under the car!!!

I agree, with the first bit. But I think you will find there is less room under car, perhaps slightly more clearance to the ground which is what I think you mean.

When I get to the point of upgrading turbos twin 3" all the way to the back of the car... wooohooo!!!!

"Ten Four" for $250 you can't really go wrong, buy it, fit it, if it is too loud for your liking then f**k it off for something more suitable.

Cheers mate, bought and collected it today (had a dent so i got it for $150 lol). It's basically a complete xforce system inc cat. Has middle muffler and rear. Question: Will the whole lot bolt up to stock front pipes or do I need to get some to suit? (Last question and very thankful cheers.)

Here's a awesome paint diagram to help explain..

edfe.jpg

Edited by Ten Four

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
    • Hi. Sry iam not a mechanic and iam not at the car atm so i dont know 100% but they told they measure those and even try to change those. AFM they have two. Coils are new a they have my old one too. Plugs too. ECU...we have 25 NEO stock and Nistune 25 NEO.   But i dont know if any one those could be the problem and why/if/what can cause this, Only thing they did not check is fuel...but that walbro 255 is new(like 1,5 years)... That fuel pressure gauge idk...but i let them know Any suggestions?   EDIT: how can they know if it is like you say he ECU pull power when it reaches a specific boost level that is too high? Tha car has boost controler
    • Can you clarify what you mean by boost cut, do you mean it misfires both when under load (driving) and when stationary and out of gear? Or does the ECU pull power when it reaches a specific boost level that is too high (boost control issue)? Does it occur at idle with no throttle? When you say "the ECU is OK", what ECU is it and why do you think it is OK? Have you used the NEO ECU, and if so do you have a MAP sensor attached? Same for the AFM, why do you think it is OK? Do you have any way to put a fuel pressure gauge on it (even just a mechanical one between the fuel filter and fuel rail)?
×
×
  • Create New...