Jump to content
SAU Community

Recommended Posts

This may not be a problem at all, its probably just me being over protective of my car.

Currently Im running standard turbo on r34 gtt at 13psi. The turbo sounds fine up until around 10psi then it makes lick a loud flickering sounds, possible could be described as a vibration sound under heavy load. I need to do some more testing myself while driving but i seems to only happen when i put my car under heavy load once its already moving NOT on a fast take off.

I thought it may be a bit of shaft play or something along those lines.

One again I may be being over protective of my car but it just doesnt sounds right to me. Anyone got any ideas of what it may be?

Link to comment
https://www.sau.com.au/forums/topic/260760-wird-turbo-sounds/
Share on other sites

  • Replies 49
  • Created
  • Last Reply

Top Posters In This Topic

Turn the boost down.

12psi and beyond is lethal on a stock ceramic Neo turbo. The vibrations you're experiencing might well be shaft play...

How long have you been running 13psi for?

ah the better part of 3 months I guess, and I dont really drive my car llike a maniac. If its shaft play, its already starting to happen at 10psi so i may as well start looking for a new turbo regardless yeh?

nylon compressor wheel with ceramic exhaust turbine wheel

MM so I spoke to my mechanic, could be anything, worst case senario turbo is Mcrooted. could be a intercooler piping problem which could result in the turbo overworking so we have the same outcome of turbo Mcrooted. Gana look at getting it repaired and hi flowed. Or a resonably priced bolt on.

  • 2 weeks later...

so this is really starting to concern me as i would have thought, if this weird vibration im getting above 10psi was the turbo i would have expected it to die by now... i probably need to get a recording of it, but its difficult as it only happens when the car is moving, if i park the car and rev the engine it doesnt happen :S

Its like a vibration sound could be closely related to the sound of a helicopters blades starting to pick up speed.

paul is waaaaay more learned than me :) so i'd be inclined to list to him, but yeah, the reason why i asked about the BC because i've just recently found out they can make a ticking noise when coming onto or around boost.

we just put some foam behind the solenoid to stop the ticking. It "could" be what's happening to you, but you are running a decent amount of boost for a stock turbo

paul is waaaaay more learned than me :P so i'd be inclined to list to him, but yeah, the reason why i asked about the BC because i've just recently found out they can make a ticking noise when coming onto or around boost.

we just put some foam behind the solenoid to stop the ticking. It "could" be what's happening to you, but you are running a decent amount of boost for a stock turbo

So ive found out it could be compressor surge, non the less, get new highflow turbo, plenum, airflow meter and injectors done this week, so we will see waht happens.

I highly doubt its detonation as this car is so well looked after, gets a FULL services every 5,000 km's. The engine has only done jsut over 100,000 or so Km's and has had the timing belt and everything done. Never gets touched by anyone bar my mechanic who i trust with my car more than I trust myself. The car is never thrashed, infact its very unlikely the cars see the likes of that 13psi more than 4 times since it was last tuned.

But the car will be tested and dynod this week and ill post up dyno charts and any problems we encounter in the process.

So ive found out it could be compressor surge, non the less, get new highflow turbo, plenum, airflow meter and injectors done this week, so we will see waht happens.

I highly doubt its detonation as this car is so well looked after, gets a FULL services every 5,000 km's. The engine has only done jsut over 100,000 or so Km's and has had the timing belt and everything done. Never gets touched by anyone bar my mechanic who i trust with my car more than I trust myself. The car is never thrashed, infact its very unlikely the cars see the likes of that 13psi more than 4 times since it was last tuned.

But the car will be tested and dynod this week and ill post up dyno charts and any problems we encounter in the process.

Detonation is down to the tune not the general upkeep of the engine .. even brand new engines can have det.. its all in the tune i.e ignition timing.. are you running an aftermarket ecu or just the standard one? did you check the base timing when the timing belt was done? these could be some possibilities , not having a go at you or your tuner just trying to help..

Goodluck with it

Detonation is down to the tune not the general upkeep of the engine .. even brand new engines can have det.. its all in the tune i.e ignition timing.. are you running an aftermarket ecu or just the standard one? did you check the base timing when the timing belt was done? these could be some possibilities , not having a go at you or your tuner just trying to help..

Goodluck with it

ah ye hi understand that but I trust the tuner I used as he learnt from matt spry. Yeh I have a nistune vg30 chip.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...