Jump to content
SAU Community

Recommended Posts

Just thought I'd share with you some very handy info I was given tonight (by a Nissan tech).

Its easy to check the ecu fault codes - something I didn't realise.

I believe the below would also be in the manual...

(btw MIL = Malfunction Indicator Lamp - otherwise known as CEL / Check Engine Light - its orange and on the right hand side of the dash in the M35).

ACCESSING:

NOTE: To access trouble codes, accelerator pedal position (APP) sensor must be functioning correctly.

  • Ensure accelerator pedal is fully released
  • Switch ignition ON. DO NOT start engine
  • Wait 3 seconds
  • Within 5 seconds, repeat the following 5 times:
  • > Fully depress accelerator pedal.
  • > Fully release accelerator pedal.
  • Wait 7 seconds.
  • Fully depress accelerator pedal and hold.
  • After approximately 10 seconds MIL will start flashing.
  • Fully release accelerator pedal.
  • Trouble codes are now displayed by MIL.
  • Count MIL flashes.
  • Compare to trouble code table.
  • Each trouble code consists of four groups of one or more flashes.
  • Ten flashes in a group indicate '0'.
  • The first group of flashes indicate the 'thousands' of the trouble code.
  • The second group of flashes indicate the 'hundreds' of the trouble code.
  • The third group of flashes indicate the 'tens' of the trouble code.
  • The fourth group of flashes indicate the 'units' of the trouble code.
  • A short pause separates each trouble code group.
  • A long pause separates each trouble code.
  • Switch ignition OFF.

ERASING:

  • Ensure accelerator pedal is fully released.
  • Ensure ignition switched OFF for at least 10 seconds.
  • Switch ignition ON - DO NOT start engine.
  • Wait 3 seconds.
  • Within 5 seconds, repeat the following 5 times:
  • > Fully depress accelerator pedal.
  • > Fully release accelerator pedal.
  • Wait 7 seconds.
  • Fully depress accelerator pedal and hold.
  • After approximately 10 seconds MIL will start flashing.
  • Fully release accelerator pedal.
  • Trouble codes are now displayed by MIL.
  • Fully depress accelerator pedal for more than 10 seconds.
  • Fully release accelerator pedal.
  • Trouble code 0000 should be displayed.

Mine showed the code 0000 (10 flashes x 4 times) so didn't solve the problem I was looking for but at least I know all the sensors are working etc. :D

Edited by pixel8r
Link to comment
https://www.sau.com.au/forums/topic/261557-ecu-fault-codes-the-easy-way/
Share on other sites

Just realised the above is all in the manual. For those who dont know, you can find all of this an much more related info in the infinit G35 service manual which you can find online - do a google search. The infiniti G35 is what we know as the skyline V35. :pirate:

There's also more diagnostics for checking fault codes on other systems in the car too.

I managed to get it to work eventually for me and got 0000 also.

No closed to knowing why idle is 150rpm too high but I will start looking for leaks around the throttle body and a few other areas.

Cheers

Andy

it was weird i tried that so many times and it didnt work on mine

Did you get it to the point where the MIL start flashing?

Read below for the plain english version...(by me)...

You may need to use a stopwatch or something to count the seconds.

Turn ignition to ON (dont start engine).

Wait 3 seconds

Then over the next 5 seconds, push the accelerator all the way to the floor and then release it fully - do this 5 times quickly within these 5 seconds.

Then wait a further 7 seconds.

Now push the accelerator all the way to the floor again and hold it for 10 seconds until the MIL starts flashing.

When you see it start to flash after 10 seconds, release the accelerator straight away

the light should then keep blinking - giving you the fault codes. it will flash up 4 codes, pausing between each. it will blink slowly for the first group, then fast for the next 3 groups. 10 flashes in a group = '0'.

ie. code 0123 would be 10 flashes, pause, 1 flash, pause, 2 flashes, pause, 3 flashes, long pause, repeat...

turn the ignition to OFF when you're done - this will exit the diagnostic mode.

next time you start the car it will be back in the normal driving mode.

I just gave it a go myself, first time I didn't get it to work.

Then I closed the driver's door incase that had anything to do with it and when I counted the seconds I used the old school method (1001, 1002, 1003 etc.)

It worked and I also got a return code of 0000 :D

This is a good thing I assume!

  • 1 year later...

Hi all,

Just reading this info, but wondering where to find the fault code info? The infinity G35 manuals I can find are all for the 3.5l v6 non turbo. Am I missing something?

I'm after code info for a m35. Sorry for the old post resurrection!

  • 1 month later...
Just thought I'd share with you some very handy info I was given tonight (by a Nissan tech).

Its easy to check the ecu fault codes - something I didn't realise.

I believe the below would also be in the manual...

(btw MIL = Malfunction Indicator Lamp - otherwise known as CEL / Check Engine Light - its orange and on the right hand side of the dash in the M35).

ACCESSING:

NOTE: To access trouble codes, accelerator pedal position (APP) sensor must be functioning correctly.

  • Ensure accelerator pedal is fully released
  • Switch ignition ON. DO NOT start engine
  • Wait 3 seconds
  • Within 5 seconds, repeat the following 5 times:
  • > Fully depress accelerator pedal.
  • > Fully release accelerator pedal.
  • Wait 7 seconds.
  • Fully depress accelerator pedal and hold.
  • After approximately 10 seconds MIL will start flashing.
  • Fully release accelerator pedal.
  • Trouble codes are now displayed by MIL.
  • Count MIL flashes.
  • Compare to trouble code table.
  • Each trouble code consists of four groups of one or more flashes.
  • Ten flashes in a group indicate '0'.
  • The first group of flashes indicate the 'thousands' of the trouble code.
  • The second group of flashes indicate the 'hundreds' of the trouble code.
  • The third group of flashes indicate the 'tens' of the trouble code.
  • The fourth group of flashes indicate the 'units' of the trouble code.
  • A short pause separates each trouble code group.
  • A long pause separates each trouble code.
  • Switch ignition OFF.

ERASING:

  • Ensure accelerator pedal is fully released.
  • Ensure ignition switched OFF for at least 10 seconds.
  • Switch ignition ON - DO NOT start engine.
  • Wait 3 seconds.
  • Within 5 seconds, repeat the following 5 times:
  • > Fully depress accelerator pedal.
  • > Fully release accelerator pedal.
  • Wait 7 seconds.
  • Fully depress accelerator pedal and hold.
  • After approximately 10 seconds MIL will start flashing.
  • Fully release accelerator pedal.
  • Trouble codes are now displayed by MIL.
  • Fully depress accelerator pedal for more than 10 seconds.
  • Fully release accelerator pedal.
  • Trouble code 0000 should be displayed.

Mine showed the code 0000 (10 flashes x 4 times) so didn't solve the problem I was looking for but at least I know all the sensors are working etc. :verymad:

Guy's I'm having problems with my Airbag light keeps flashing

Ive got a 2001 Stagea ARX4 and theres nothing wrong with the airbags but the light keeps flashing.

Is there a way for me too reset the light cause its possing a problem with me.

Will the ECU Fault Test reset the Airbag light or is there another way.

Im in need of Stagea Help

Dont Worry allready fixed the problem LOL :)

If it's the same problem I had it may return in a few weeks. Mine seems to set off now and again under boost going uphill (atleast that was when it went off last time).

I have a code but as of yet it has been of no use, I have taken pictures of the error screen(s) that came up and am waiting for them to be translated in the hope it sheds more light on the issue.

It has been suggested it could be the seat belt pretensioner but as of yet I have not investigated this as I had disconnected and reconnected the cables under the drivers seat and reset the ecu.

Let me know if you have further issues, we may need to discover the problem together.

I still have the airbag light up but it matches the Mil light that's constantly on.

The reset works for a while which is why I think the tensioner is the issue as they are known to fail, its a bad connection somewhere.

Bis-e-Bee, If you could send me the error screen and codes I will see if the nice Japanese lady at work will translate it, she did a wonderful job on the ecu pinouts.

I still have the airbag light up but it matches the Mil light that's constantly on.

The reset works for a while which is why I think the tensioner is the issue as they are known to fail, its a bad connection somewhere.

Bis-e-Bee, If you could send me the error screen and codes I will see if the nice Japanese lady at work will translate it, she did a wonderful job on the ecu pinouts.

have you tried to get the Error code on the Informeter? There is in the Setup menu a DTC option which brings up the code.

  • 2 months later...

still havent gotten it to work... will try again now.

im wondering if my aftermarket alarm has anything to do with it..as the alarm has a 30 second timer before it disables ignition and requires disarming for the engine to start.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I got back to Japan in January and was keen to get back on track as quickly as possible. Europe is god-awful for track accessibility (by comparison), so I picked up a first-gen GT86 in December just to have something I could jump into right away. The Skyline came over in a container this time and landed in early January. It was a bit battered after Europe, though—I refused to do anything beyond essential upkeep while it was over there. The clutch master cylinder gave out, and so did the power steering. I didn’t even bother changing the oil; it was the same stuff that went in just before I left Japan the first time. Naughty. Power steering parts would’ve cost double with shipping and taxes, so knowing I’d be heading back to Japan, I just postponed it and powered through the arm workout. It took a solid three months to get the car back on the road. Registration was a nightmare this time around. There were a bunch of BS fees to navigate, and sourcing parts was a headache. I needed stock seats for shaken, mistakenly blew 34k JPY on some ENR34 seats—which, of course, didn’t fit—then ended up having the car’s technical sheet amended to register it as a two-seater with the Brides. Then there’s the GT86. Amazing car. Does everything I want it to do. Parts are cheap, easy to find, and I don’t care what anyone says—it’s super rewarding to drive. I’ve done a few basic mods: diff ratio, coilovers, discs, pads, seat, etc. It already had a new exhaust manifold and the 180kph limiter removed, so I assume it’s running some kind of map. I’ve just been thrashing it at the track non-stop—mostly Fuji Speedway now, since I need something with higher speed after all that autobahn time. The wheels on the R34 always pissed me off—too big, and it was a nightmare getting tires to fit properly under the arches. So I threw in the towel and bought something that fits better. Looks way cleaner too (at least to me)—less hotboy, less attention-seeking. Still an R34, though. Now for future plans. There are a few things still outstanding with the car. First up, the rear subframe needs an overhaul—that’s priority one. Next, I need to figure out an engine rebuild plan. No timeline yet, but I want to keep it economical—not cutting corners, just not throwing tens of thousands at a mechanic I can barely communicate with. And finally, paint. Plus a bit of tidying up here and there.  
    • Nope, needed to clearance under the bar a little with a heat gun, a 1/2" extension as the "clearancer", and big hammer, I was aware of this from the onset, they fit a 2.0 with this intake no problems, but, the 2.5 is around 15mm taller than a 2.0, so "clearancing" was required  It "just" touched when test fitting, now, I have about 10mm of clearance  You cannot see where it was done, and so far, there's no contact when giving it the beans Happy days
    • It's been a while since I've updated this thread. The last year (and some) has been very hectic. In the second-half of 2024 I took the R34 on a trip through Germany, Italy, France and Switzerland - it was f*cking great. I got a little annoyed with the attention the car was getting around Europe and really didn't drive it that much. I could barely work on the car since I was living in an inner-city apartment (with underground parking). During the trip, the car lost power steering in France - split hose - and I ended up driving around 4,000kms with no power steering.  There were a few Nurburgring trips here and there, but in total the R34 amassed just shy of 7,000kms on European roads. Long story short, I broke up with the reason I was transferred to Europe for and requested to be moved back to Japan. The E90, loved it. It was a sunk cost of around EUR 10,000 and I sold it to a friend for EUR 1,500 just to get rid of it quickly. Trust me, moving countries f*cking sucks and I could not be bothered to be as methodical as I was the first time around.
    • I assume clearances were all a-okay?
    • Shock tower brace is in +5Kw....LOL  
×
×
  • Create New...