Jump to content
SAU Community

Recommended Posts

If you have a hose kinking, a Unicoil might stop it? Most Auto Shops should have them.

Yeh tried a unicoil, problem is you then don't have enough space on the hose to get a hose clamp on.

Yeh tried a unicoil, problem is you then don't have enough space on the hose to get a hose clamp on.

insert copper pipe into your oil line and bend it as you need. The bends I have are impossible without kinks, my dad rigged this up for me its fair awesome.

insert copper pipe into your oil line and bend it as you need. The bends I have are impossible without kinks, my dad rigged this up for me its fair awesome.

Would have worked, but it's another cost.

To be honest I think the best way is to get a custom braided line made up. No problems, perfect fit, easy. Expensive, but by the time you get to this stage you will be ready to sell your mother to get the farken thing finished :P

Hey Sarge, I had a look at your on road video for SS2 spool up in 2nd from back near page 100. It looks pretty good, and from Stao's dyno chart on it looks like full boost around 3700 for a higher gear.

What do you find that one like to live with? Have you wished it was more responsive or more "top endy"at all? How has it been with this newest actuator you've been running?

Hey Sarge, I had a look at your on road video for SS2 spool up in 2nd from back near page 100. It looks pretty good, and from Stao's dyno chart on it looks like full boost around 3700 for a higher gear.

What do you find that one like to live with? Have you wished it was more responsive or more "top endy"at all? How has it been with this newest actuator you've been running?

My old skyline had a high flowed turbo with 2835 internals. It was mega responsive and made really nice power. This is certainly not as responsive but damn its soooooo enjoyable you live with it. When it comes on hard and you get some nice smooth quick shifts, the power does not stop. That video shows you I think 3rd gear to 6krpm. Had I dropped it in second it would take a second or two to be in full song, but that video was demonstrating the car building boost from low gear, and its pretty good. You can feel first gear runs out of oomph up top, but thats only natural, its not running out, your tires are just spinning so you lose that push in your chair feeling, so what I do is generally shift earlier, around 5500rpm rather than 7krpm. This also helps prevent wheel spin when entering 2nd. Definitely alot better with the new actuator and tune. I was actually very happy with the tune on the soft actuator and didn't intend to go any higher but my tuner said you may as well because the potential for power is definitely there so I did.

With better boost control I think the power line will hold all the way to red line, you can see it tips over abit up top where boost starts to fall. Then you can see the low boost line it holds and keeps going up beyond red line because boost is steady.

This is certainly not as responsive but damn its soooooo enjoyable you live with it.

This is how it is with my turbo at the moment. I'm only getting full boost by 5000rpm, but my god it's a fun 2000rpm :P

Need to work out my midrange issues glare.gif

You know what the responsiveness difference is between your turbos and say the SS1PU or whichever is next down in the "SS" range?

It sounds like yours has similar come on to the G3 which flows more. I thought all the SS ones favoured punch over top end hit.

man that really is waaaay too laggy - waiting till 5k rpm to get full boost, but I guess its got something to do with your engine conversion. why not turn the car back to stock, sell it and buy a proper GT-T and work from there?

man that really is waaaay too laggy - waiting till 5k rpm to get full boost, but I guess its got something to do with your engine conversion.

NA motor will have even LESS lag.

Oh my motors not NA. I imported a smashed GTT from Japan and transplanted everything.

Problem is there is no difference between my car and a 'proper' GTT. It has everything, it was all literally taken straight out of a GTT and put into my car. Everything. The issue is what we wired up and what we didn't. Things like traction control which I never wanted and never knew could cause issues like this. So I need to figure out what it is exactly that is upsetting the ECU and how it can be fixed.

Worst case scenario I have to ditch the NIStune and get something like the ViPEC plug-in.

Yeh tried a unicoil, problem is you then don't have enough space on the hose to get a hose clamp on.

ah, didn't think about the length.. are you using the standard metal long angled drain pipe off the turbo base? If so could you just use a unicoil with the other type of turbo fitting that is just a small pipe fitting?

ah, didn't think about the length.. are you using the standard metal long angled drain pipe off the turbo base? If so could you just use a unicoil with the other type of turbo fitting that is just a small pipe fitting?

Yes, well we ended up just cutting the hard pipe about 2 inches from the bottom and then used two pieces of short length hose with the off-cut hard pipe in between them. The standard rubber return hose was only JUST too short, like I could get it on to both the turbo hard pipe and the sump return, but it was only just on there so wasn't enough room for a hose clamp. So only needed to be extended a little bit.

I'm not really happy with how we fixed it, it's a bit back-yardish so I'll be getting a custom braided line with fittings made up to replace it soon. When it comes to oil and hotness, I don't want to be messing around with potentially dodgy connections.

I was going to join Sarge in the SS2 crew but the castings aren't available til February, and I'm too antsy in the pantsy with Xmas spending spirit so I'm in the G3 brigade instead.

I'll throw some results up when it's all together :thumbsup:

Nah i plan on using nuts bolts and glue

Self tappers and a cordless > zip ties and duct tape > nuts bolts glue.

I also have an RB25 head (DET) that has been VCT deleted to suit RB30 block, has also had exhaust valves retouched. Is a fairly bare head. I will sell this if anyone else wants to venture down this path (or if you need a spare Crans)

I also have an S2 RB30 block yet the crank has gone walkabout (unsure where it is and needs oversized bearings). Has the factory line bolt holts etc for turbo.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
    • So, a bit of a side trip, but one that might be interesting for people with JDM cars and japanese head units. I know @Pac previously posted about a carplay/android auto adapter he installed which used the AUX input, and @V35_Paul put in one of the Tesla style units that replace both screens. The option I went with was a Lsait LLT-YF-VER5.87_2 (https://www.alibaba.com/product-detail/Lsailt-8GB-Android-Multimedia-Interface-for_1601187633672.html). Price was $1,150 for a single unit although they are much cheaper if you are willing to buy 2....$857ea. Make you you get the version 2 not version 1, it is faster and has a better UI - this is the manufacturer listing: http://www.lsailt.com/product/348.html. BTW if you've never bought from Alibaba before, don't be concerned....these guys can't stay in business unless they are responsive, ship fast etc, they were excellent (probably faster shipping than most local places) So, this was my task for a lazy Sat afternoon....looks complex but was all done in a few hours (it probably helps that I had some of it apart before so it was a bit familiar). I also decided to add a HD USB drive recorded at the same time and the unit also supports an aftermarket reverse cam (if you don't want to retain factory) and also AV in and HDMI out It looks much worse than it is, in fact in was genuinely all plug and play (no custom wiring at all). This video was pretty good (skipped a few steps), unfortunately they are an Aussie seller but no longer sell this unit (I guess Carplay/AA adapters are easier to install and much cheaper) https://www.youtube.com/watch?v=T5hJfYOB8Dg
×
×
  • Create New...