Jump to content
SAU Community

Recommended Posts

After riding shotgun in my mates series 2 Stagea i was wondering if its possible to install a tiptronic gearbox,selector,etc in a series 1?

The gear changes[using the buttons on steering wheel]seemed a lot quicker & more responsive than when i manually change them on my series 1

i dont know how well it will bolt up to mounting points, the bell housing pattern should be the same but you'd have to check the g/box to chasis mounts as well as tailshaft compatibility. also you would have to run a S2/R34 ecu as the auto is controlled by this (not a straight swap, rewiring would be needed maybe additional sensors???).

i'd say it could be done, but i think the time, effort and money involved in doing it wouldn't be worth it. it could be better spent on a manual conversion or shift kit and other upgrades for the auto you have.

Edited by QWK32
  • 7 years later...

Any news here ?

I have the same idea.

Stagea S1 and S2, both have the RE4R01A Transmission.

If i want to upgrade my S1 to a Tiptronic, do i have to change the gearbox or only the shifter and the gearbox-ecu ? (I dont need the shiftoption on my steeringwheel)

Hope you guys understand what i want :-D

Best Regards

Andi

Any news here ?

I have the same idea.

Stagea S1 and S2, both have the RE4R01A Transmission.

If i want to upgrade my S1 to a Tiptronic, do i have to change the gearbox or only the shifter and the gearbox-ecu ? (I dont need the shiftoption on my steeringwheel)

Hope you guys understand what i want :-D

Best Regards

Andi

It would be a lot easier and better to sell the S1 and buy a S2 (especially if you don't already have the Neo engine).

  • 7 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...