Jump to content
SAU Community

Recommended Posts

i did the change. also went from a pfc to a wolf v500, with a much more in depth tune so i can't really coment on possible response loss, as i actually gained a lot of throttle response.

only ill effect i noticed was a small increase in the amount of times the car cranked over before it started. like maybe half a second.

There are many automakers who use MAP based systems with no problems at all, so why would you have problems with a map based standalone? If there were problems you can probably chalk it up to bad tuning or just a poorly designed standalone. I have zero problems with my standalone map based system even though I have a 5bar map sensor. Cold start, Drive-ability, Closed loop wide band Cruise, and deceleration are perfect.

Edited by maximajim

I went from ECR33 PFC L-jetro and converted it to run the GTR's D-jetro, Being that I mapped both setup's I can say this, the D-jetro was much easier to get nice dead stable AFR's, Drivability is better and fuel consumption is up by .5L better per 100km. (this was with no other mods done at all besides ECU change, I use FCedit, dual widebands, EGT and dual knocklinks when mapping RB's)

Best thing, no idle mess around! car just runs better all round. D-jetro's idle stabilization by timing is fantasic as well! almost as good as VEMS's

so far then .. it sounds all good.

I wasn't told map has any "problems" but that it isn't a good choice if you plan

to do mountain driving, as altitude (or big temp changes) muck with the tune vs maf.

My tuner says map will "feel different" in a possibly negative way, he didn't elaborate.

And people on sau have posted before that map is 'for race cars' and maf is for street,

and someone else on sau said map didn't work as well with multiple throttle bodies.

So I figured I'd ask if people had experienced a car before vs after with as much else

the same.

Edited by moneypit
I would say buy a ecu based on his recommendation or find another tuner who is competent in tuning a map system.

He should know that a good standalone will have temp and barometric trims (if needed).

He recommended going map, ecu is hks f-con,

but he just said it will feel different, and indicated I might not prefer it.

MAP sensor here too. Given the choice, i'll always go MAP over AFM. The number of AFM related issues that seem to pop up all the time is crazy. I went through 3 AFMs on my old car, and it still never was quite right.

MAP sensor here too. Given the choice, i'll always go MAP over AFM. The number of AFM related issues that seem to pop up all the time is crazy. I went through 3 AFMs on my old car, and it still never was quite right.

100% agree

MAP user here :D

so far then .. it sounds all good.

I wasn't told map has any "problems" but that it isn't a good choice if you plan

to do mountain driving, as altitude (or big temp changes) muck with the tune vs maf.

My tuner says map will "feel different" in a possibly negative way, he didn't elaborate.

And people on sau have posted before that map is 'for race cars' and maf is for street,

and someone else on sau said map didn't work as well with multiple throttle bodies.

So I figured I'd ask if people had experienced a car before vs after with as much else

the same.

The issue with multi throttle bodies and MAP, is the turbulunce.

You can get the same MAP reading, for a different throttle reading, and it plays havoc.

Good ECU's, like the Adaptronic, Motec, (I also believe Haltech, ViPEC and Autronic) run MAP vs TPS tuning.

I run MAP with the Adaptronic, and it has no issues at all.

Actually, it has quite a few benefits... I can run NO BOV, and not have a single issue.

I run an oil coated air filter, and not have it flood my AFM giving shit readings, resulting in poor idle...

Yeah mine doesnt take long to crank, and doesnt hunt on cold start. It does everything "normally" compared to an AFM based ECU.

....Well, except for having dramas when the AFM's get dirty and play up :D

Ford XR6 Turbo runs map and no issues there. So the whole map = race car is a little off.

The 1JZ and I believe 2JZ also run MAP...

Lots of manufacturers cars run MAP from the factory

My car takes a couple of cranks to fire, but that is purely the ECU, and NOTHING to do with it being MAP based.

I went through 3 AFMs on my old car

Brand new each time or 2nd hand? I'd be interested to hear the reasons why 3 brand new AFM's would have died in a short period.

If 2nd hand, then well... thats pretty much a pointless statement :D

Every AFM that i put in (new) works/worked fine without issue.

Ive played around with 2nd handies lately (due to time constraint) and had nothing but problems, but i accept that because im playing around with used parts and not brand new ones.

That said - go with what the tuner reccomends. He is tuning it afterall...

Straight MAP was poor on light throttle compared to AFMs but I had multiple throttle bodies (RB26). Redid the tune with MAP over TPS (combination of the 2) and found driveability every bit as equal as stock AFMs.

Best point => if I blow a cooler pipe/vacumm hose at the drags I can drive it home as is... unlike AFMs which would instantly foul the plugs. Best move I ever made was getting rid of the AFMs.

I went for a MAP because my tuner prefers it, he put it this way to me, although the AFM is a good bit of gear he has had more problems with that one piece of equipment than any other but finding out it is the AFM to be the problem is the real reason he prefers the MAP sensor, as for driveabilty I didnt really notice anything except the power increase.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
×
×
  • Create New...