Jump to content
SAU Community

Recommended Posts

As you guys may know, you are required to have 1 X 900ml fire extinguisher for supersprints and 2 X 1 kg extinguishers for touring tarmac rallies. (Interestingly neither require you to have a Roll cage)

If you only attend these items rarely and still want to retain your car without extinguisher holes this is what I did:

Buy a 1 metre flat bar of 25 X 3mm Aluminium $5.00 from Bunnings

Cut it the length from front seat mount to front seat mount (about 47cm but measure first)

Drill holes to coincide with front anchor bolts to the seat, then remove the bolts, fit the bar mark the position of the holes in the extinguisher mounts (must be steel, plastic no longer acceptable) Drill these holes out with a 4mm drill and use a pop rivet to mount the extinguisher to the bar. Mount bar (now with extinguisher mounted) to mseat anchors using the original bolts.

It is now a two min job to install and remove the extinguisher when you need it.

Dominic

Link to comment
https://www.sau.com.au/forums/topic/26341-fire-extinguisher-mounts-for-skyline/
Share on other sites

Dominic, that sounds like a good, complete option.

I took another low impact approach, just put the extinguisher braket thru the bolt holding the rear seat to the floor (behind passenger seat). Still nice and close if I ever need to grab it.

Duncan

very clever....i have an extinguisher and would like to keep it in the skyline ( some years back a modified turbo car of mine caught fire and was saved by a passer by with an extinguisher so since i carry one in that car ) but didnt wanna go drilling around...now i will try your method.

Cheers.

sorry, was that request pics of mine? its pretty basic, nothing to show here :D Just take bolt holding seat bottom down off, put mounting on, put bolt back thru

Dominic's solution sounds better, I'm just no good with stuff, and couldn't find a fabricator. Typerlc on these forums recommended the same trick a while back.

  • 4 months later...

yahahaha

*Throws shovel aside

just purchased an extinguisher and mounted it ala duncans above post.

is it safe to leave it in there all the time?

Quote from the box

"In a car, place the extinguisher within reach of driver. the extingusher must be secure to the vehicle.

To ensure the extinguisher is ready for use at all times, do not store in direct sunlight or under a windscreen as temperature of 48 degrees (120F) are to be avoided"

does a car not get a lot hotter than 48 degrees if left in the sun for a couple of hours?

I'm not sure of the offical word on safety but mine lives in the car at all times including the 60 degree NT days :D

On the other hand 2 ppl were injured at the supercars at wakefield from extinguishers blowing up the other weekend

the one i bought yesteday was kiddie (kiddy?) i think.

i asked the dude there if there was ant difference between the two to choose from, they were both the exact same price and he said it wouldn't surprise him if they were the exact same product too, just a different box.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...