Jump to content
SAU Community

Recommended Posts

Today in peak hour traffic I got a little too close to the car ahead...

Two cars shot down the left of me and the car ahead and then both tried to cut back in again... ...So the woman ahead of me slammed her breaks on... ...And sadly I was looking over to my right to try and merge right to make room for the two tools thinking that the second car was about to try and merge into where I was... ...but he went ahead of her and she slammed on the breaks... ...She tried to get the number plate of the second car but only got the first two letters...

And here's the damage...

n733856829_2814967_5712691.jpg

n733856829_2814960_4411494.jpg

n733856829_2814965_4909454.jpg

n733856829_2814957_5555217.jpg

n733856829_2814964_458609.jpg

n733856829_2814959_3327195.jpg

I'm hoping it is all plastic damage... ...Doesn't look like any metal is bent... ...Apart from the few metal clipping points just behind the grill and left headlight... ...which pushes the headlight up a little and I can't close my bonnet... ...It clips down but doesn't latch... ...And I'm guessing I'm going to need a new bar... ...because it looks like this isn't fixable...

What annoys me most is I see day after day people shooting down those left lanes in peak hour traffic intersection after intersection and using the service lane to jump ahead of the traffic... ...I guess this time it was my turn to get caught by these poo heads...

Link to comment
https://www.sau.com.au/forums/topic/263844-i-made-a-boo-boo/
Share on other sites

ouch man! sorry to hear. lucky the headlight didnt get broken. yeah i was heading to the westside in peak hour today was awful to see the amount of people who cut in turning lanes and literally just drive infront of you almost hitting the front/side of your car.

ur taking it well mate....

atleast it wasnt that bad.... but kinda makes the car look like she is crying now :)

if u dont have to drive the car I would be taking out that headlight to prevent anymore damage... (they cost 500 a light from nissan if you cant find one on the forums) so keep it safe...

only thing I know Id be doing is using my skyline power to chase after the mofo....

gl with it mate!

There's really no other way to take it... ...I was only doing about 30 to 40 after taking off from lights... ...It wasn't the woman's fault... ...If anything I was too close...

I know what caused it... ...And I'm not usually in that lane on the way home to try and avoid things like tools shooting up that extra left lane and cutting back into the left lane... ...I usually leave a huge gap that almost always gets taken up by some tool trying to rush home...

Just one of those things...

I will get my break balance checked at my next service... ...I do kinda feel that my front wheels locked up way too quick for the slow speed... ...Last service I had the rear disks/pads/calipers/bearings done... ...maybe there's something there...

The other thing is I need my car for work... ...So any time off the road is time lost income... ...I guess I can take the light out for a week or two... ...I don't drive at night much... ...if at all...

sorry to hear about it, nothing shits me more than when approaching glenferrie road outbound on toorak rd, and the trams are terminated there, and everyone is backed up patiently in the left lane, and then people start pulling out and cutting in on people just before the intersection.

Oh well...this is what happens when you follow too closely...

The headlight looks fine but the mounts will be broken...its useless.

The bar looks pretty badly damaged, it will probably cost you just as much if not more to repair it as getting another s/h one.

In Clayton theres a place called A1 Bumpers or something like that, they do good plastic welding.

Usually in an accident if the situation has caught you off guard and you just slam the pedal instead of squeezing, there will be no weight transfer and the fronts will just lock.

Got a couple of quotes today... ...anywhere between $1200.oo and $1800.oo... ...Looks like I'll be doing it through insurance...

Only one clip on the back of the headlight is damaged... ...the reo bar is damaged... ...girll is fine... ...but the metal clipping point in the center is bent...

I like the S1 bar more than the S2... ...And have no idea what you mean by "banana bar"... ...Please send photos...

One place said they'd never seen the silver surrounds on a 33... ...And had no idea where to get replacements in silver... ...another said they could just send the headlights off and the backing would be replaced... ...the rest of the headlight could be fine...

Anyway... ...off to call Just Cars now... :)

Got a couple of quotes today... ...anywhere between $1200.oo and $1800.oo... ...Looks like I'll be doing it through insurance...

Only one clip on the back of the headlight is damaged... ...the reo bar is damaged... ...girll is fine... ...but the metal clipping point in the center is bent...

I like the S1 bar more than the S2... ...And have no idea what you mean by "banana bar"... ...Please send photos...

One place said they'd never seen the silver surrounds on a 33... ...And had no idea where to get replacements in silver... ...another said they could just send the headlights off and the backing would be replaced... ...the rest of the headlight could be fine...

Anyway... ...off to call Just Cars now... :)

Silver surrounds are off a 33 4 door. My panel guy had no problem getting a new one after a merging incident.

if you are handy with fibreglass, you could fix the front bar yourself, but its tricky because resin and plastic don't bond well.

easiest way to do that is drill 1/8th holes either side and tie it all up with mig wire

(after you get it back into rough position by heating it up and pushing it back into place)

then when you fibreglass over it the mig wire has all the strength that used to be there and the fiberglass goes over to start the smoothing process

tricks of the trade ;) (when i was a panelbeater apprentice :) )

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...