Jump to content
SAU Community

Recommended Posts

Can anyone tell me if it IS normal for a HKS 2530 turbo to make spooling noises (like a whistle)?

Is this normal induction noise.

:(

Also, does a bellmouth dump pipe provoke noise at high rpm from the wastegate opening? (like a muffled screamer?) ... or would this signify a leak between the turbo and dump pipe?

Link to comment
https://www.sau.com.au/forums/topic/264033-hks-2530-turbo-induction-noise/
Share on other sites

I have the same turbo. With an atmo BOV no whistle. If I run a recirc, I can hear the compressor whine until the BOV closes.

Yeah, I've heard the faint 'whistle' is normal for HKS turbos ... just needed reassuring ... someone else says 'no'.

My BOV is recirc back into intake.

I'm guessing the higher pitched noise is either the wastegate opening to release ex gases into my bellmouth dump pipe ... or its a loose nut (or gasket) around the turbo-to-dump or turbo-to-manifold.

I've got a 2530 on my R33 GTST and it whistles too. I too wasn't sure if this is right. It has been checked and no vacuum leaks could be found. Mine starts to whistle at about -0.8 Bar and then it becomes harder to hear after about 0.5 Bar or somewhere there. I'd be interested to hear some other peoples experiences. I've got the standard plumb back BOV, standard air filter and HKS dump.

What boost are you rinning?

- intake piping... rubber or metal

- Pods... filter type, metal frame, plastic frame and so on

The causes of the most obvious "Turbo whistle" noise that HKS turbos are often recognized by is anti-surge compressor covers - HKS GT-RS, GT2835, GT3037, T51Rs and T62Rs all have it though I wasn't aware of anything smaller having that kind of housing though I guess they could have done it with the GT2530s etc just to be special :)

depends on the noise it makes. The Shinnning noise is normal, If its making a Zzzz... zz... noise, very noticeable when you switch off the car then it means bearing cartridge needs to be checked.

  • 5 weeks later...

Iv'e noticed a whistle with my HKS 2530 to be more pronnounced after changing to plumb back, its like the turbo spools up to a certain speed at like -0.08bar then as it comes onto boost gets harder to hear and goes away as soon as its on 0.5bar + my 32 is tuned to run around 16psi but the whistle noise im more aware of now since the change from full atmo to plumb back.... does it have to do with the way the air circulates around the intake pipe?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...