Jump to content
SAU Community

Recommended Posts

Boss Automotive is another place as they are the diff specialist

+1, I had my r31 fitted with an LSD made by Boss and it was awesome. Wasnt cheap because I went all out but it was damn good...

-D

i am in the mist of looking at getting my r33's diff shimmed

got a quote of like $600 for removal, shimming and re fitting the diff

which i dont think its over the top as they are the speciallist in it and from memory they were going to be replacing the bearings as well

A shimm diff it basically a locker

Also shimms wear down unlike welding... which break :wacko:

I reckon 1.5 or 2way LSD is the way (orrrr the welder)

1.5 is more streetable

2way is a bit iffy, depends where, when how you drive

I shimmed mine LSD. Was tight as a b!tch, great to have 150% locked. Saying that though, one day through marion car park reversing out a car park..... f**king BANG :D ..... it broke.

It impresses da chickz uleh

-D

HAHAH yeah it like

Hey uleh... Look at me!

Ehh Ehh Ehh Ehh Ehh Ehh Ehh (trying to do a U-turn)

LOL Shimms r fun but wear down over time and need adjusting

Check out http://www.skylinesaustralia.com/forums/Di...Gt-t164288.html

Edited by MYCEF3

Just remember, more tractive force from the diff center puts a lot more load on drive shafts, cv joints and bearings. As well as on the rest of the drive train and mounts.

Edited by Jamesrb25

I will shim peoples diffs for $250 + you supply the oil and gasket if needed (HICAS diffs a little extra unless you pull it out). People can also came and watch while I do it and that way they can learn how it is done them selves. This is handy because as people have mentioned above they will wear so after a couple of years they will need to be done again.

What people are saying about a shimmed diff's being a locker isn't necessarily true. You can shim then to be a locker but if you select the right shim it will just be a really tight V-LSD and it won't skip. Also the Shimming is preloading the viscus cuplink and isn't actually changing the back lash, the bearing shims do this not the cuplink shims.

Edited by D_Stirls

i found a bit over 3mm (over both sides) was best for me, i recently just chucked in 2x 1.6mm ones in over the top of the standard ones, locked her up good and tight lol

just be careful, if u go too thick like i did, it wont fit in the housing anymore, i had to create custom bearing shims (thinner) so it fit in lol.

please correct me if i'm wrong, but i believe my diff is the same as S15 (Helical diff) not viscous

am i still able to shimm this diff? i'm intending to use this for drift, only until i can afford a 2 way LSD

looks pretty easy to do DIY

cheers for the help guys, and keep the constructive criticism coming :woot:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hang on. Let me get this straight. The desire is to have coilovers, BC in particular, to be MORE comfortable on Sydney roads than stock suspension? Well, that's obviously not right. BCs have crude damping design at the very best, and typically hard spring rates. BC stands for Billy Cart. And then, the desire is to put in some shitty old worn out stockers, to get it blue slipped and then put the BCs back in? And then.....what? Not worry about getting pulled up by the Plod? Because you seem to have raised a worry about paying for engineering (which actually does solve all your legality problems) and still getting pulled up.... but the only problem there is that if/when that happens you have to show your paperwork at the inspection station. Whereas, if you just swap in borrowed shitty old stockers to get it slipped now, and then you get defected in the future, you have to go find more shitty old stockers then too. You course of action looks like this set of options: Buy brand new stock type dampers, and springs. probably cost a bit more than $1k all up, but will last for the remaining life of the car. Put them in, pass inspection, drive on them forever more. Hell, they could even be really nice Bilsteins and Kings or other lower&stiffer springs if you wanted. Get the car engineered as is. ~$1k. Buy new Shockworks coilvers (or MCA) and also pay for engineering. You're spending a lot more here. But these will be the best things that you could drive around on.
    • Might be worthwhile hitting up Facebook's groups, I know most of them contain terrible people and scammers - however you might be able to find someone that's in Sydney with factory suspension you could purchase and/or hire. Just do not send any form of money anywhere, in person cash only.
    • Thanks @Duncan Ride height is fine. I think it's almost stock tbh. Happy to share a pic. I don't actually have a regular mechanic as haven't lived in Sydney too long. Could you or anyone recommend any shops in Sydney?
    • You just need a different blue slip shop (preferably one you regularly use as a mechanic), and make sure the coil overs are as close as possible to standard height
    • yeah the sugar refining companies were pushing for the same in Oz originally, all fuels were going to have 10% ethanol to make them "cheaper" (noting, that the loss in l/100 might be greater than the decrease in price). I guess they won that fight in Canadia
×
×
  • Create New...