Jump to content
SAU Community

Recommended Posts

some cars have them stock, and some dont...

millions of people run without one, and i have NEVER heard of a turbo dying because of a no BOV situation...

you'll be fine deano...

  • Replies 53
  • Created
  • Last Reply

Top Posters In This Topic

Ok, here's the thing:

Compressor surge (commonly known as dose) is bad for your turbo. There is no real dispute about this. Whats in dispute is how bad it actually is, ie the simile mentioned before was a tennis ball against a brick wall.

What you got to remember is that if any given turbo has a life of 120K kms then compressor surge isn't gonna do you any favours in regards to life expectancy. From my experiences so far compressor surge is not going to have any affect (other than increased lag b/w gears) in the short term, but if ur looking to keep ur car for a few years and/or have an old turbo on there, I would def be putting on a BOV.

P.S., Ive got a blitz one for sale if u need it :)

how about a bov wound down fairly tight? tight enough to clearly hear compressor surge. when there is enough pressure, it releases back into recirc, but otherwise it doesnt.

thats how mine is, and i dont see any fuel economy issues, or added lag between changes.

a bit off topic, but still in the ballpark :)

Edited by Munkyb0y

This is what Corky Bell has to say about it. But with a name like that, i'm not sure what to believe :blink:

Compressor surge is the rapid fluctuation of turbine speed caused by the throttle's being closed under boost. Rapidly spinning air compressors (turbos) can go unstable briefly when this occurs. The fluctuating speed can be damaging to the turbo and the accompanying noise is obnoxious. The condition can be alleviated with a compressor bypass valve that opens as the throttle closes and allows air exiting the turbo to vent back to the front This keeps the flow up. Many modern turbo cars are equipped with such valving, but seldom are they big enough to handle high-flow, high-boost systems, A useful fringe benefit to these valves is that they reduce lag and perceptibly increase fuel economy.
Compressor surge is the rapid fluctuation of turbine speed caused by the throttle's being closed under boost. Rapidly spinning air compressors (turbos) can go unstable briefly when this occurs. The fluctuating speed can be damaging to the turbo and the accompanying noise is obnoxious. The condition can be alleviated with a compressor bypass valve that opens as the throttle closes and allows air exiting the turbo to vent back to the front This keeps the flow up. Many modern turbo cars are equipped with such valving, but seldom are they big enough to handle high-flow, high-boost systems, A useful fringe benefit to these valves is that they reduce lag and perceptibly increase fuel economy.

Obnoxious my ass!!

Edited by PM-R33

My mate put a turbo on a MX5 BOV'less and it lasted about 5 months before the shaft play was quite bad. No shaft play to begin with.

He has another one of the exact same turbo (he baught my old turbos, R34 standards) and is running it with a BOV and it is fine and has lasted already longer then the last one. In that mind that does it for me.

Running a AFM setup Nissan style, likely to hurt economy if anything. Certainly wont help it

Hmm i guess it depends on the car. Running no bov or an atmo bov should have the same effect on fuel economy. I run an atmo bov and still manage about 480km to a tank before the fuel light comes on. (Standard ECU)

My thoughts: Red top RB20DET + FMIC never had a BOV factory, wound it up to 14psi ran it for 3+ years pulled the turbo off and it was exactly the same as you'd expect a 120,000km turbo to be. A little bit of oil but nothing out of the ordinary, it still boosted hard. Car drove great. Put an R33 turbo on and continued running with no BOV, zero problems.

RB25DET S2, blocked the BOV off and the car ran like shit (I still have the factory SMIC). I think the newer ECUs are far more sensitive with their mapping and the airflow changes upset it.

I would have no qualms whatsoever running without a BOV, providing the ECU could handle it.

there is always shaft play.

Did a turbo swap on a mate's RB25, the brand new HKS we put on had about 3x the shaft play of his stock item. Excessive shaft play is a problem, minimal is not.

blades are spinning at several thousend rpm, them coming to a complete stop when air is pushed back through? it has 2 do sumthing

No. Do you think compressor wheels are made of paper mache? They have to be strong enough to compress air while being hot and spinning at a hundred thousand RPM. Do you think a little bit of chuffing noise is going to upset them? Doubt it.

What you got to remember is that if any given turbo has a life of 120K kms then compressor surge isn't gonna do you any favours in regards to life expectancy.

Most turbos last longer than that, but say 120k with a BOV and 115k or 110k without. Who cares?

My mate put a turbo on a MX5 BOV'less and it lasted about 5 months before the shaft play was quite bad. No shaft play to begin with.

Too many variables, or just bad luck. He was probably more careful with the second turbo as well.

Hmm i guess it depends on the car. Running no bov or an atmo bov should have the same effect on fuel economy. I run an atmo bov and still manage about 480km to a tank before the fuel light comes on. (Standard ECU)

logically speaking it wont have the same effect...

but every car/driver is different... i said it wouldnt help. :)

Here's a simple test.

First, obtain a tennis ball in the opposite hand that you throw with.

Subsequently, go outside your house, find a nice spacious brick wall, and through it at the wall.

Then, inspect the wall to see if there is any damage...

Same principle applies to air hitting the turbo fins.... :):ph34r:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
    • Final update!!! Got the front bar fitted and sprayed and all sorted now. My cutouts worked great and the indicators aren’t just falling off. 😂  
    • Is this a brand new LSD? if so, have you followed any break/bed in procedure for it? Usually involves heaps of figure 8 patterns, a fluid flush.
    • It's TWO steering wheels actually. 😛 one for each hand They are wheels, and they steer!
×
×
  • Create New...