Jump to content
SAU Community

Recommended Posts

I think the whiteline bars are $400 - $500 front and rear.

The thing is that I don't want to make the car grossly uncomfortable so I don't want urethane/nolathane bushes.

I got the shocks and strut bars. There's still some money to be spent on brakes as well.

Car is fine and I have a boring 1,000km run in to look forward to.

T.

Link to comment
https://www.sau.com.au/forums/topic/27167-skyline-handling/#findComment-571998
Share on other sites

Sway bars (actually "anti-roll" bars) stiffen the suspension to prevent weight transfer to the outside wheels during cornering. The beauty of them is that they don't affect the straightline ride comfort, which you would get by fitting heavier shocks / springs to achieve the same result.

You should invest in the nolathane bushes - it will reduce the compliance of the suspension, ie the suspension is less likely to change dynamically from its static settings. But they won't contribute noticably to ride (dis)comfort.

It's generally pretty complex subject. I would suggest you invest a few dollars in some books (1 by Fred Puhl is pretty good at explaining the physics, but gets technical when showing how to calculate all the variables).

Link to comment
https://www.sau.com.au/forums/topic/27167-skyline-handling/#findComment-572130
Share on other sites

First thing you need to do is get someone who knows what they are doing to have a look at the car and see what it is doing now. It may be that nothing is suited and the balance etc is all over the place and even that it is too low now and thus does not allow enough suspension travel.

Mick.

Link to comment
https://www.sau.com.au/forums/topic/27167-skyline-handling/#findComment-572144
Share on other sites

Tony, nolathene bushes won't make the ride uncomfortable - the hard Jap springs are already perfect for doing that :rofl:

As blind_elk says, swaybars are perfect for improving handling without affecting ride comfort. What they basically do is link your left and right suspension arms together. As the outside suspension arm travels upwards in a corner, it pushes the swaybar upwards as well. The swaybar then transfers some of this upwards movement to the inside suspension arm, and the net result is that the outside arm compresses less, and you get less body roll through the corner.

Skylines (and most other cars) already have swaybars, but they're not very thick. Whiteline have stiffer/thicker bars, which do the job better. You usually need a bit of bodyroll though, otherwise your inside wheels will start to lift off mid-corner. Happens to the Bathurst V8's fairly often.

Link to comment
https://www.sau.com.au/forums/topic/27167-skyline-handling/#findComment-572841
Share on other sites

Handling on my car is slightly worse than it used to be.

On my car at least, it's a bit of a double edged sword.

There's 12 or 16 levels of adjustment.

The ride used to be harsh but zero body roll.

Now it's soft and pliable but rolls a fair bit.

So maybe the bars might fix that to some degree.

T.

Link to comment
https://www.sau.com.au/forums/topic/27167-skyline-handling/#findComment-573418
Share on other sites

Way to go is a full Whiteline kit. You might find it a little firm on day one but it is so controlled that the ride soon feels fine, even over bumpy surfaces. I opted for the full version with the nylon bushes and adjustable bars because I use the car for supersprints. It cost around $2200 installed and has been a great investment.

Link to comment
https://www.sau.com.au/forums/topic/27167-skyline-handling/#findComment-575472
Share on other sites

I have full coil over suspension by a company called DORF. Its fully adjustable up and down and soft and hard. Its on the softest setting and its damm bumpy. I mean really bumpy in that if your accelarating and go over a bump your wheels come off the ground. Also while going up my driveway, I have 1 wheel (left rear) in the AIR. The car is so stiff it doesn't have any play. Its great for handling, like a car on rails, and with no body roll.

THe disadvantage apart is that if you try to launch the car it wheelspins majorly.

The major advantage, watch those girlees t i ti es bounce around like mad!

:uh-huh:

Link to comment
https://www.sau.com.au/forums/topic/27167-skyline-handling/#findComment-580858
Share on other sites

I've never really thought about this and can see why soft suspension might seem the best for getting off the line but consider this:

If the car sits right down at the back under heavy accelleration, weight transfer may also cause considerable negative camber and therefore less contact area between the tyre and the road. Camber kits, after all, are designed to minimise negative camber on lowered cars and avoid reducing tyre contact area.

Also, I've never seen a serious drag car with soft suspension...

Link to comment
https://www.sau.com.au/forums/topic/27167-skyline-handling/#findComment-581373
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...