Jump to content
SAU Community

Recommended Posts

easily overloaded tho

say u wire in power from the ciggie lighter

then plug a GPS into the ciggie lighter can cause it to overload and blow the fuse.

They're on two different circuits. The lighter power and light power sources are different.

I had a guy come to me wanting me to wire in 8 gauges (yes 8) in his car. What I had to do was use relays to power both sides and use the spare in his fuse box for overload.

If you're only running the one gauge you'll be okay to pick it up from the lighter light circuit, even better if you used LED's to keep the current draw down.

+1 for cigerette lighter. the light uses a serperate power feed but the same earth as the power for the lighter itself.

mines been running off there faultlessly for near a year. Using an LED in my boost gauge but :bunny:

Link it off the ring around the cig lighter. That turns on with headlights

Its the top connector in the picture below;

gallery_46113_2344_49202.jpg

Instructions on how to get to it is here;

http://www.skylinesaustralia.com/forums/R3...em-t204874.html

I'm also trying to find wire clips (that let you tap into power from an existing wire), but can't for the life of me find them on the Jaycar website, are they called something else?

I'm also trying to find wire clips (that let you tap into power from an existing wire), but can't for the life of me find them on the Jaycar website, are they called something else?

Scotch lock quick splice connectors. You can also use T-taps.

Should have mentioned. Go to any car parts mob like Malz, or Stupid Cheap. You'll have a better chance of finding them there than at Jaycar who are more electronics oriented.

I'm also trying to find wire clips (that let you tap into power from an existing wire), but can't for the life of me find them on the Jaycar website, are they called something else?

Dick Smith have some that wrap around the source wire, and provide a spade connection for the branching wire.

o cheers for the info

my friend must of linked it to the wires going to the actual ciggie lighter .. not the circle light around it.

so if i link a boost gauge to that wire it will dim it self at night?

o cheers for the info

my friend must of linked it to the wires going to the actual ciggie lighter .. not the circle light around it.

so if i link a boost gauge to that wire it will dim it self at night?

If you use the cigarette light, it will be full brightness at night, and not light at all during the day. Though if you lightsource the climate control uses, it will be full brightness during the day and dim at night (that's if the light will work on the dim voltage whatever it be)

so if thats the case i would connect the purple dimmer wire on the guage to the climate control and the red power wire to the ign wire or something similar?

Now that I think about it, putting the dimmer wire on the climate control is a bad idea, since you would need the climate control always turned on.. I didn't think about that consequence since my CC is always on. Stock headunits have a dimmer function iirc, if you have a aftermarket headunit just look for a wire not connected (im guessing nobody keeps the dimming function with A/M decks)

you dont need the light to be on during the day?

just go straight to the cig lighter light. Easiest and most effective. Dont worry about diming and stufff. If your that worried put a variable resistor in the circuit somewhere....

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hope you aren't too sore after that one, might take a day or 2 to notice yet and I guess it is a loooooong drive home. On the bright side, tube frame front end is a thing at superlap, right?
    • https://www.facebook.com/share/p/18rmVb1SKB/ 
    • The chart of front pressure to rear pressure (with one being on the x axis and the other being on the y axis) is not a straight line on a typical proportioning valve. At lower pressures there is a straight line with one slope, and at higher pressures that changes to a lower slope. That creates a bend in the line at that pressure, called the knee point. If you do not change the proportionng as the pressure gets higher, you will suffer excessive pressure (at one end of the car or the other, depending on which way you look at the proportioning action) and then get lockups at that end. The HFM BM57, from my memory of previous discussions, is based on the BM57 from a different car (to a Skyline), with a different requirement for the location of the knee point and the distribution of pressure front to rear, and so is not a good choice for an upgrade on a Skyline. Here's a couple of links to some old posts, one from here, one from elsewhere. A lot of it pertains to adjustable prop valves, but the idea is the same. There are plenty of discussions on here about this issue from al the many years of people wanting a cheap/accessible option. https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/ https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/  
    • Yeah dunno why johhny posted that here with no context, just post on FB/insta bro where he put it up?  Laine had an off at T4 during Thurs prac, he's ok, car is less than perfect, they are done for the weekend, he can fill in the rest. Bando also binned it like 100m up the road.   
    • I feel there must have been a FB/insta post and the weekend did not start well at all I hope everyone is all okay
×
×
  • Create New...