Jump to content
SAU Community

Recommended Posts

Symptom - Car cranks but does not start (hot or cold)

There is fuel pressure at the line, pump is operating and priming correctly. There is a good spark.

Now here is the confusing part - on initial start, there is no injector pulse. I thought easy fix, its probably my CAS. Changed with another working unit tested on another car. It starts! Switched the engine off. Try to start again, cranks but no start. Once again, no injector pulse.

When i remove the CAS and spin it by hand, the pump primes and the injectors pulses. Reinstall the CAS and it starts. But when I switch it off, same problem reoccurs.

I've checked all the main wiring loom, make sure there's no short to earth. I've checked all earths and wiring. The battery is new. Measures 12.4Vs and 14.5Vs whilst running (alternator is charging). Whilst cranking it drops to 10.2V which is acceptable.

My theory is that the starter motor is drawing too much current when cranking, causing the CAS not to send the proper signal. Does anyone have any further ideas that I might need to check? I know its hard to diagnose a car over the internet without seeing it, but just want to hear any other ideas just in case I have left something out.

By the way, the car did receive a whole bunch of upgraded bits. Just to name a few that might affect it - Bosch 040 fuel pump and Bosch 363 injectors with R32 GTR ballast resistor, Z32 AFM, 80mm Throttle body. The rest of the mods I fail to see how it could affect starting.

Cheers!

Link to comment
https://www.sau.com.au/forums/topic/274278-starting-issues-need-ideas/
Share on other sites

Get rid of the ballast resisters and put in injectors that suit the car.

Had exactly this problem with a customer with a PowerFC Pro and GTR injectors (Dano4127). ripped out the resisters, made a new loom for the SARD 550's I had laying around and bang, starts every time. It had something to do with the injector driver in the ECU not operating correctly with that particular setup. Spoke in length with contacts in Japan and it turns out some of them have different drivers to others so cannot be wired that way.

That's a fair call about the injectors. I'm running a remapped RB20 ECU with Nistune.

My question is now, what's the difference between me turning the CAS by hand and the camshaft doing it whilst cranking? It should technically still prime and pulse the injectors whilst cranking?

It could be dropping voltage to the injector drivers while cranking. It could be something to do with current issues with the resistors in place causing the drivers to not fire while the starter motor is drawing what it needs.

Just a thought.

I never went into it in massive detail as I could see the most uncomplicated solution so I just fixed it. I would have liked to know exactly why but unfortunately time was not permitting. Let me know if you find out the reason.

If you think your car is drawing too much current, hence the voltage drop, does the car start when you roll start it?

like get 2 of your mates to push the car down the street, and clutch it to life, if that doesn't work that's not the problem then.

try starting the car without the AFM plugged in.

Sounds like the CAS is acting up, my car acted the same, would start in the beginning if you pushed it but it got worse and worse until it wounldnt start at all. Pulled the CAS and gave it a spin by hand, sounded like a peppergrinder :blink: Changed it and everything was good!

That's a fair call about the injectors. I'm running a remapped RB20 ECU with Nistune.

My question is now, what's the difference between me turning the CAS by hand and the camshaft doing it whilst cranking? It should technically still prime and pulse the injectors whilst cranking?

it could be that you have a broken cam (have seen this before in a mates ca18) or there is a short in the CAS so that it is earthing out when bolted to the block.

but i would be looking at other things first like voltage dropping when cranking

Cheers for the input guys.

Just to clarify, the engine does start but only after I have manually spun the CAS. As soon as the injector pulses, I can reinstall the CAS and it starts.

Its not the AFM and its not the CAS. When the engine is running, it receives all signals correctly and runs fine. I've checked the end of the cam to make sure there's no damage to the half-moon shaft.

I've just bought another starter motor and will be installing it this weekend.

  • 1 year later...

thread revival, didnt want to start new one, car wont start, only cranks

what i have tested so far:

fuel pump relay - ok

fuel pump primes - ok

fuses (in-cabin and engine bay) - ok

fuel pressure - 43psi

battery (13v, 11v whilst cranking) - ok

ignitor - swapped with another known working one

ignitor earth grounded - yes

voltage at injector - yes

pfc sensor check - ok

disconnected maf - still no start

spark with coilpack attached - FAIL

R34 CAS, yet to remove, however have read broken locator wont stop it starting

continuity testing to coilpack loom - yet to do

check voltage at starter motor - yet to do

broken cam - possible??

Q:

is cas and ignitor only culprit that would cause no spark issue?? any other things i can look at..

anyone wanna lend a R34 CAS i can test with??

if there is injector pulse than the CAS is ok, the ecu gets its firing order signal for injector and spark from the CAS so if one works then they should both work.

you need to check with an LED test light if theres a pulse on the ecu side of the ignitor when cranking, this will tell you if the ecu is sending the signal to the ignitor. it will be very faint when you check it.

if there is no pulse here the check at the ecu itself, if there is none here than you might need to try another ecu,

will PFC sensor check pickup the issue, as it came back normal

I'll open the PFC to check for burnt tracks and re-check wiring

any specific pin I should be testing?

Is there a relay near the PFC, I remember ages ago of one clicking in that area

update:

swapped in a new odyssey pc1200 battery, still no closer to getting it started

i have voltage at the injector plugs although this is different to injector pulse which i cant hear during cranking with screwdriver

if so, that would point the finger at the CAS right?

when measuring voltage at ignitor, do i have to earth out the E during cranking in order to get voltage reading?

also have re-plugged the ECU and relays near it, yet to test voltages at the pins

btw, car started briefly with the new battery for bout a minute, idled normally, could hear the injectors being their noisy normal self, then on its own it splutter few times and died

question:

assuming CAS is fine, and its the power wire to the coil in the loom thats broken or bad (ie. no spark), will cranking still cause injectors to wet the spark plugs??

i will pull CAS out over the weekend and rotate by hand to test if the injectors click etc

also only one of the relay by the ecu click with ignition on however 12v is present on both relays

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Power is fed to the ECU when the ignition switch is switched to IGN, at terminal 58. That same wire also connects to the ECCS relay to provide both the coil power and the contact side. When the ECU sees power at 58 it switches 16 to earth, which pulls the ECCS relay on, which feeds main power into the ECU and also to a bunch of other things. None of this is directly involved in the fuel pump - it just has to happen first. The ECU will pull terminal 18 to earth when it wants the fuel pump to run. This allows the fuel pump relay to pull in, which switches power on into the rest of the fuel pump control equipment. The fuel pump control regulator is controlled from terminal 104 on the ECU and is switched high or low depending on whether the ECU thinks the pump needs to run high or low. (I don't know which way around that is, and it really doesn't matter right now). The fuel pump control reg is really just a resistor that controls how the power through the pump goes to earth. Either straight to earth, or via the resistor. This part doesn't matter much to us today. The power to the fuel pump relay comes from one of the switched wires from the IGN switch and fusebox that is not shown off to the left of this page. That power runs the fuel pump relay coil and a number of other engine peripherals. Those peripherals don't really matter. All that matters is that there should be power available at the relay when the key is in the right position. At least - I think it's switched. If it's not switched, then power will be there all the time. Either way, if you don't have power there when you need it (ie, key on) then it won't work. The input-output switching side of the relay gains its power from a line similar (but not the same as) the one that feeds the ECU. SO I presume that is switched. Again, if there is not power there when you need it, then you have to look upstream. And... the upshot of all that? There is no "ground" at the fuel pump relay. Where you say: and say that pin 1 Black/Pink is ground, that is not true. The ECU trigger is AF73, is black/pink, and is the "ground". When the ECU says it is. The Blue/White wire is the "constant" 12V to power the relay's coil. And when I say "constant", I mean it may well only be on when the key is on. As I said above. So, when the ECU says not to be running the pump (which is any time after about 3s of switching on, with no crank signal or engine speed yet), then you should see 12V at both 1 and 2. Because the 12V will be all the way up to the ECU terminal 18, waiting to be switched to ground. When the ECU switches the fuel pump on, then AF73 should go to ~0V, having been switched to ground and the voltage drop now occurring over the relay coil. 3 & 5 are easy. 5 is the other "constant" 12V, that may or may not be constant but will very much want to be there when the key is on. Same as above. 3 goes to the pump. There should never be 12V visible at 3 unless the relay is pulled in. As to where the immobiliser might have been spliced into all this.... It will either have to be on wire AF70 or AF71, whichever is most accessible near the alarm. Given that all those wires run from the engine bay fusebox or the ECU, via the driver's area to the rear of the car, it could really be either. AF70 will be the same colour from the appropriate fuse all the way to the pump. If it has been cut and is dangling, you should be able to see that  in that area somewhere. Same with AF71.   You really should be able to force the pump to run. Just jump 12V onto AF72 and it should go. That will prove that the pump itself is willing to go along with you when you sort out the upstream. You really should be able to force the fuel pump relay on. Just short AF73 to earth when the key is on. If the pump runs, then the relay is fine, and all the power up to both inputs on the relay is fine. If it doesn't run (and given that you checked the relay itself actually works) then one or both of AF70 and AF71 are not bringing power to the game.
    • @PranK can you elaborate further on the Colorlock Dye? The website has a lot of options. I'm sure you've done all the research. I have old genuine leather seats that I have bought various refurbing creams and such, but never a dye. Any info on how long it lasts? Does it wash out? Is it a hassle? What product do I actually need? Am I just buying this kit and following the steps the page advises or something else? https://www.colourlockaustralia.com.au/colourlock-leather-repair-kit-dye.html
    • These going to fit over the big brakes? I'd be reeeeeeeeaaaall hesitant to believe so.
    • The leather work properly stunned me. Again, I am thankful that the leather was in such good condition. I'm not sure what the indent is at the top of the passenger seat. Like somebody was sitting in it with a golf ball between their shoulders. The wheels are more grey than silver now and missing a lot of gloss.  Here's one with nice silver wheels.
    • It's amazing how well the works on the leather seats. Looks mint. Looking forward to see how you go with the wheels. They do suit the car! Gutter rash is easy to fix, but I'm curious about getting the colour done.
×
×
  • Create New...