Jump to content
SAU Community

Recommended Posts

well i worked out if i made 270.9awkw @ 6800rpm;

theoretically @ 8500rpm it will make 338.62awkw (if i use the formula of 39.84awkw per 1000rpm).

before anyone rips me apart, i know that the power level is not consistent across every 1000rpm & the power may even drop off higher in the rpm hence this is just an average number & 'guesstimate'

...this is calculated @ 10psi with cams @ 0degrees.

with more than double the boost & tuned cams it 'should' piss in over 400awkw :P

now where's that flux capacity & white coat!

Seems like you've already got them on marko :blink:

  • Replies 477
  • Created
  • Last Reply

Top Posters In This Topic

Hi guys,

I had the car tuned yesterday @ CRD :banana:

Refer to attached graph, it made 405awkw @ 23psi with 930nm of torque (to put this into perspective, my previous rb26 on the same dyno & turbo's made 750nm)!

I asked jim what this equates to rwkw, he said about 445rwkw.

Rev limit is set at 9000rpm as jim stated that the engine just wants to keep revving, the above figures are based on 8500rpm (who said rb30's don't rev?)...reason for this, he wants me to avoid touching the limiter as he said its not the best thing for the engine.

It drives like an absolute weapon & what a difference the extra capacity makes, it really is phenomenal & to be honest I haven’t seen jim so excited about any of my past tunes & setups, he is a strong advocate of the rb30.

His words:

"you have the best combo for the street, the average torque increase is HUGE & will feel like an rb26 with 480awkw"

"wait till you drive it, it will be completely different to any gtr"

Something else he mentioned which I noticed was that the car was squirming from left/right on the dyno, the reason is due to torque steer which he has only seen on 1 other gtr with an OS Giken 3.0ltr with T51R & made 480awkw.

Jim wanted to go to 24psi but my actuators wouldn’t allow this as they are set @ 0.7bar, he suggested at this boost level it will make 415awkw.

currently @ 23psi he said it is very safe for hot days & has purposely ran it a bit richer.

My next step (if I want more power) is to run E85, upgrade to 1600cc injectors & run 1.2-1.5bar actuators. This will give me an average gain of 50awkw (i.e. over 450awkw)

He was very happy with the results considering the engine ran stock valves, intake plenum & throttle bodies.

He was very impressed with the way the engine performed on the dyno - all Kudo's to Greg @ ProEngines, thanks mate!

post-8728-1247788866_thumb.jpg

Edited by Marko R1

Nice result mate!

Always good to see a project end up with such a great result

You've inspired me to move $1k out of my "Holiday" fund into my "RB30" fund

She looks like she pulls nice and hard up top, what size Kelfords did you use?

Hi guys,

I had the car tuned yesterday @ CRD :P

Refer to attached graph, it made 405awkw @ 23psi with 930nm of torque (to put this into perspective, my previous rb26 on the same dyno & turbo's made 750nm)!

I asked jim what this equates to rwkw, he said about 445rwkw.

Rev limit is set at 9000rpm as jim stated that the engine just wants to keep revving, the above figures are based on 8500rpm (who said rb30's don't rev?)...reason for this, he wants me to avoid touching the limiter as he said its not the best thing for the engine.

It drives like an absolute weapon & what a difference the extra capacity makes, it really is phenomenal & to be honest I haven’t seen jim so excited about any of my past tunes & setups, he is a strong advocate of the rb30.

His words:

"you have the best combo for the street, the average torque increase is HUGE & will feel like an rb26 with 480awkw"

"wait till you drive it, it will be completely different to any gtr"

Something else he mentioned which I noticed was that the car was squirming from left/right on the dyno, the reason is due to torque steer which he has only seen on 1 other gtr with an OS Giken 3.0ltr with T51R & made 480awkw.

Jim wanted to go to 24psi but my actuators wouldn’t allow this as they are set @ 0.7bar, he suggested at this boost level it will make 415awkw.

currently @ 23psi he said it is very safe for hot days & has purposely ran it a bit richer.

My next step (if I want more power) is to run E85, upgrade to 1600cc injectors & run 1.2-1.5bar actuators. This will give me an average gain of 50awkw (i.e. over 450awkw)

He was very happy with the results considering the engine ran stock valves, intake plenum & throttle bodies.

He was very impressed with the way the engine performed on the dyno - all Kudo's to Greg @ ProEngines, thanks mate!

Nice result, well done, that's a strong one Greg. What's the scale along the bottom of the dyno graph? RPM (1K to 10K) or KPH (0 to 200)? The 405 4wkw is around 675 bhp, so there should be plenty left in the 1000 cc injectors? Are you sure it will be necessary to go to 1600 cc's for E85? After all there is plenty of flow and pressure available from 2 x 044's, so lifting the fuel pressure is a no cost option if required.

Cheers

Gary

if anyone is contemplating on building an rb26/30 - just do it!

these gtr's were born to carry these torque monsters.

Mmm i seem to recall someone saying that (and a lot more) to you in a pub about a year ago....

thats what i thought greg :( more bling!

i was waiting for my 'gay request' to bite me on ass lol

I have to admit Marko, you're the first person I've done an engine for that's sent me an email saying "I know this may seem like a gay request..." I'm pretty accommodating but there are limits... :P

Nice result, well done, that's a strong one Greg. What's the scale along the bottom of the dyno graph? RPM (1K to 10K) or KPH (0 to 200)? The 405 4wkw is around 675 bhp, so there should be plenty left in the 1000 cc injectors? Are you sure it will be necessary to go to 1600 cc's for E85? After all there is plenty of flow and pressure available from 2 x 044's, so lifting the fuel pressure is a no cost option if required.

Cheers

Gary

hey gary - the scale along the bottom is kph (0-200).

the fuel system is up to the task for e85, however, the 1000cc are @ 90% injector duty...e85 requires 30% more fuel & if i gain 50awkw i definitely need 1600s

I have to admit Marko, you're the first person I've done an engine for that's sent me an email saying "I know this may seem like a gay request..." I'm pretty accommodating but there are limits... :down:

well greg...u have given me as you quoted "a nice fat curve" (dont worry guys, im married)

hey gary - the scale along the bottom is kph (0-200).

the fuel system is up to the task for e85, however, the 1000cc are @ 90% injector duty...e85 requires 30% more fuel & if i gain 50awkw i definitely need 1600s

are you serious? :down: theres gotta be something funky going on there somewhere caus it doesnt make sence. whats rail pressure set at?

I agree, 1000's should only be running at about 70% to make 400rwkw

forget the power levels guys...its torque that eats injector duty.

example...my old engine with 700cc jobbies could muster 450+ with headroom...new set-up with more torque had them maxed out at 450. The difference between the two engines was the completely different torque curve, one looked like a mountain peak...the other was flat and wide.

running indy blues at a reasonable duty cycle is a lot more sensible than trying to push the 1000's by upping the base on them.

Edited by DiRTgarage
forget the power levels guys...its torque that eats injector duty.

example...my old engine with 700cc jobbies could muster 450+ with headroom...new set-up with more torque had them maxed out at 450. The difference between the two engines was the completely different torque curve, one looked like a mountain peak...the other was flat and wide.

running indy blues at a reasonable duty cycle is a lot more sensible than trying to push the 1000's by upping the base on them.

well its about time somebody explained this on the thread & it actually makes sense, thanks TW.00.GL!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
    • You haven't driven many modern cars then have you? Most of them have sfa steering feel with their stupid electric bullshit steering systems.
×
×
  • Create New...