Jump to content
SAU Community

Removing Harmonic Balancer On R32 Gtr

phat25t

By phat25t,
in General Maintenance

 Share

Recommended Posts

phat25t Community Regular

phat25t

Posted
Posted

Hey I'm trying to remove the nut in the centre of the harmonic balancer with a power bar, I just want to make sure it needs to be turned anticlockwise because I know I've removed one on another car that was backwards(it needed to be turned clockwise to loosen.

Cheers ,

Steve

32_Dave Mentor

32_Dave

Posted
Posted
yep its a normal bolt. letft loosy, righty tighty.

could be vft though

they are VVVFFT (very very very f**king f**king tight) if its never been out before.

believe its 140-150 ft pound 14-15kg

get a steel pipe on the end of your breaker bar. if u got a flywheel lock use that or if your ghetto put a bolt in the block where the box would bolt up and pivot off it using a screwdriver slotted into the flywheel teeth. both methods work :D

cheers

Duncan Grand Master

Duncan

Posted
Posted
they are VVVFFT (very very very f**king f**king tight) if its never been out before.

believe its 140-150 ft pound ....

even worse on gtr, 400lb/ft. for some reason gtst is only 150 odd.

br3ndan Mentor

br3ndan

Posted
Posted

A good way of doing this is...

position ur breaker bar so its leaning on the ground put the key in the iginition and turn her over. The car will un do it for you.

Only attempt this if you are confident...im sure they didnt need to be said tho.

turbo_brian Community Regular

turbo_brian

Posted
Posted (edited)

http://www.enginebuildermag.com/Content/Si...00000006981.jpg

Use the right tools and to it properly.

You can get a hammer-tool and socket, place socket onto bolt, hammer-tool into socket (dont know it's actualy name or I would have put up a picture, but it's got an arm about 10cm long, then another arm from this about 80cm long, you hammer the longer arm and it shock-loads the bolt right at the thread).

Or you use a tool like in the picture above, where it holds the harmonic balancer from turning, and the 2nd arm is used against the harmonic balancer's locked pressure to turn the nut (uses SFA energy to crack the thread).

Reason you dont place the car in gear, or use a fly-wheel lock is because your then placing all your force down the length of the crank shaft, and if your hitting the bolt, using a rattle gun, etc your placing shock-loads onto the crank and potentially damaging the crank.

Reason you dont use the starter is for the same reason.

Dont get me wrong, these methods work, but they place un-due force on the internals of the motor, and 'could' cause potential failure points in the future.

EDIT: Almost forgot, USE FLAT FACED SOCKETS!!!! Dont use the milling grip sockets, you will almost certainly round the nut, and then be stuffed!!!

Edited by turbo_brian
  • 1 month later...
Jmaac Proficient

Jmaac

Posted
Posted (edited)

You can remove the starter and use a screwdriver to lock the flywheel before using a breaker bar. I still couldnt loosen it first time, but you may be able to. This worked after I loosed everything up using the method below.

I ended up using an electric impact gun. It removed it easily and effortlessley. I tried the first procedure for 2 days and started to go mental over the one bolt holding me up. Use a proper impact bit and it'll absorb all those nasty 'shock loads' (crank can handle it no probs anyway).

Use a proper fitting socket (full hex/flat face) as mentioned

Also as above bush mechanic style, you can use a breaker bar on the bolt and brace it against up against the chassis and crank the motor over with your starter. I would recommend against this though as the starter will give way before the crank

Edited by Jmaac
Duncan Grand Master

Duncan

Posted
Posted
I bought a breaker bar and smashed it as hard as I could but no go, not sure what to do with it now?

you get a longer breaker bar!

easiest way to do that is put a long jack handle / pole of some sort over the breaker bar. Once you get to 1-2m long you will have enough leverage to undo it

Rowdyr32 Mentor

Rowdyr32

Posted
Posted
you get a longer breaker bar!

easiest way to do that is put a long jack handle / pole of some sort over the breaker bar. Once you get to 1-2m long you will have enough leverage to undo it

I've had a couple where I have had to put a bicycle innner tube around the balancer and then a chain from the balancer to the front tow hook and then wrap a racket strap bloody tight around the inner tube and chain. This is the only way I could get two engines bolts to crack with a 3/4 drive breaker bar and a pole with two people.

There was to much flex in the drive train and couldn't get it to stay still any other way. It would just turn with the purchase. Some are bloody tight!

  • 1 month later...
phat25t Community Regular

phat25t

Posted
  • Author
Posted

Hey guys,

I still have not been able to get this off due to time and this thing being f%$king tight. How did you guys fit an impact gun in the engine bay?? I have the radiator out but theres not enough room to get my air impact gun behind the pulley.

Cheers,

Steve

Beer Baron Grand Master

Beer Baron

Posted
Posted

sadly having it done up too tight it still far better than the ones that are not done up tight enough and come undone!!! d'oh! happens a lot and is sometimes an easy fix and sometimes will cost you an engine.

R324DR Proficient

R324DR

Posted
Posted

with the right leverage you can undo most things. i had to put my car up on a hoist, attach a very long steel bar to the breaker bar, get underneath the car, and get two people to swing off it. not the most professional way of doing it, but it worked.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      R33 GTR running -9 with no tune

      By Duncan · Posted

      Sounds like you've got an interesting adventure ahead here with local support if you have trouble! My guess is that, unboosted, you will be OK with a small upgrade like -9. What will happen is that once the stock ECU sees more airflow than it expects it will add a heap of fuel and pull a heap of timing to be safe because it can't understand how it could get that much air without there being an issue. You will see clouds of black smoke and it won't pull hard through the midrange and top end. So, overall it will be a bit frustrating but should be OK. If you are still nervous set the base timing back 2o through the CAS, but it will be even more sluggish everywhere. As said above through...this is not my guarantee your engine won't be blown into a million pieces, leaving you looking for very hard to find parts A better idea is get a computer with logging ASAP, wire in a wide band O2 sensor and a use remote tuner. I've done multiple cars this way and while it is not as good as a specific tune on a dyno they can get it 90% right. I'd suggest if you can afford an R33 GTR these days you can afford an ECU and tune. And if you can't afford that you sure won't be able to afford the rebuild if it goes bad in the meantime,.  
    • Duncan
      New kid on the block

      By Duncan · Posted

      Yeah it would be nice if someone took the time to put that sort of information together, but there are a lot of variations in looms. I think you are making this way hard for yourself if you just want to get it running....sourcing an SR20 with the right wiring will be a billion times easier than matching the RB loom to an S15 chassis. If you do end up going this way, you just need to trace every wire in the loom with a multimeter, 95% of them will go to a location you can confirm at the ECU.....and then post it up for the next person who needs it  
    • Duncan
      Coolant leak?

      By Duncan · Posted

      Just top it up with water, and keep a general idea of how much you added. It is normal for water to be pushed into and pulled out of the reservoir through the cap, and it should not be more than half full or it will be likely to overflow when hot. Any decent mechanic can do a pressure test of the cooling system to confirm if you have a leak. Keep in mind if it is only leaking a little and when hot it may well evaporate before you see it hit the ground
    • GTSBoy
      Coolant leak?

      By GTSBoy · Posted

      I'd ask the shop what they used and use that. Mixing coolants is sometimes OK, sometimes not, and you have know the details of each coolant to know whether it's a good idea or not.
    • Chupapy
      Coolant leak?

      By Chupapy · Posted

      Is it alright to top up with just another green coolant?
×
×
  • Create New...