Jump to content
SAU Community

Recommended Posts

Was looking at these mags:

94509371.jpg

But they only come in 9inch wide - is that too wide for my r32 GTST at the front? - i dont want guard rub :thumbsup:

And would i be able to stretch 215/40/17's on them too?

And lastly, my cars not low at all - so would that aid in being able to fit them?

They are 17x9 - 30 offset

Im not clewed up on mags, so it really is a guessing game for me...

Edited by Flux_nz
Link to comment
https://www.sau.com.au/forums/topic/278546-will-these-mags-fit-my-r32-gtst/
Share on other sites

are you sure it's -30 and not +30?

there is no chance -30 will look anything short of ridiculous, but +30 is achievable.

i wouldn't personally put 215s on there but if you were so inclined you could

+1

9inch +30 with scrub on the rear (if lowered). Will need to roll the guards or have some negative camber.

They will also scrub on the front depending on height.

I had +30 8inch on the front with 235/45 tyres and it would scrub. Dropped to 225 and scrubbing went away. Yours are 1inch wider so would scrub much easier in my opinion.

9inch +30 is the same design as R33 GTR rims. So best to ask any r32 gtst owner with r33 gtr rims and they will tell you a deffinite answer on fitting.

9inch +30 with scrub on the rear (if lowered). Will need to roll the guards or have some negative camber.

They will also scrub on the front depending on height.

I had +30 8inch on the front with 235/45 tyres and it would scrub. Dropped to 225 and scrubbing went away. Yours are 1inch wider so would scrub much easier in my opinion.

9inch +30 is the same design as R33 GTR rims. So best to ask any r32 gtst owner with r33 gtr rims and they will tell you a deffinite answer on fitting.

I have R33 GTR wheels on an R32 gtst with 245/45 rubber, standard-ish ride height with stiffer shocks & springs, i had to get rears rolled (not lipped) and have had no scrubbing what so ever.

Front is a different story..... 245's on the front, standard guards untouched, only when i hit a big dip or bump does it slightly scuff something on the tyre, it hasn't chopped sidewalls (I cannot see any damage what so ever to the tyre's), i use to have a pair of tyre's on the front with worn shoulders and it never scrubbed once over anything.

Tyre's rubbing shouldn't be your main concern, just slap 235's maximum on them and you should be fine with standard-ish ride height. (My 245's stick out front the guards at the front and would probably be deemed unroadworthy, next set of tyres are going to be 235's)

I would worry about the +30 offset rims effecting your roll centre and what it does to your steering & suspension.

+30 changes your roll centre and steering becomes more 'darty' over ruts and divets on the road. (each front wheel wants to roll around bumps instead of travelling up and down over them). This means constant corrections have to be made to keep it going straight. 12 months have past with the wheels on and i have had to replace steering rack bushes from all the extra movement in the rack.

Other bushes at the front have probably been prematurely worn because of the wheels.

They look fat and grip great on the twisties and track but are very compromised on the road.

More solid steering rack bushes at the front have helped quite a bit but I wouldn't recommend +30 offset on a car that has to be driven daily in the city unless you like the steering wheel jumping out of your hands.

Just my 2 cents

I have R33 GTR wheels on an R32 gtst with 245/45 rubber, standard-ish ride height with stiffer shocks & springs, i had to get rears rolled (not lipped) and have had no scrubbing what so ever.

Front is a different story..... 245's on the front, standard guards untouched, only when i hit a big dip or bump does it slightly scuff something on the tyre, it hasn't chopped sidewalls (I cannot see any damage what so ever to the tyre's), i use to have a pair of tyre's on the front with worn shoulders and it never scrubbed once over anything.

Tyre's rubbing shouldn't be your main concern, just slap 235's maximum on them and you should be fine with standard-ish ride height. (My 245's stick out front the guards at the front and would probably be deemed unroadworthy, next set of tyres are going to be 235's)

I would worry about the +30 offset rims effecting your roll centre and what it does to your steering & suspension.

+30 changes your roll centre and steering becomes more 'darty' over ruts and divets on the road. (each front wheel wants to roll around bumps instead of travelling up and down over them). This means constant corrections have to be made to keep it going straight. 12 months have past with the wheels on and i have had to replace steering rack bushes from all the extra movement in the rack.

Other bushes at the front have probably been prematurely worn because of the wheels.

They look fat and grip great on the twisties and track but are very compromised on the road.

More solid steering rack bushes at the front have helped quite a bit but I wouldn't recommend +30 offset on a car that has to be driven daily in the city unless you like the steering wheel jumping out of your hands.

Just my 2 cents

i had the tramlining issue with 235/45's on my +30 rims. Steering wheel would pull into any ruts in the road etc, was annoying to drive with.

However after dropping to 225/45, adjustable camber bushes,adjustable castor bushes and a proper alignment, the tram lining disappeared and have no issues.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
    • I also used NP   That’s were it’s seems to be the best place to fit it? All schematic shows also that it’s should be referenced from the turbo housing. But idk, I do see high hp cars without any connection or anything to their turbos, so I really don’t know how they connect their things
    • I do have loctite 243 and 246 and a few more models. I could drill it now in place and make new threads for m12 and order an4 - m12 coupling and fit that to the turbo. Run a braided hose to the EBC which I could get a an4 to 1/8npt 
    • So M12 and sealant should be fine?    NPT ” because that’s what I had and what I could get atm. 
    • Wouldn’t touch par if they gave it to me. You need to ask how much power you’re looking to make and then add about 50% to it because that’s what you’ll end up making  The factory box says no more at about 350kw or so, the upgraded synchro boxes won’t handle much over 500kw for long and at that point you’re looking at an auto or dog engagement manual,  once you’ve gone dog engagement you may as well go sequential, they cost a little bit more but it’s worth it  also while you’re at it you should upgrade the transfer case with 10 friction plates 
×
×
  • Create New...