Jump to content
SAU Community

Recommended Posts

Was looking at these mags:

94509371.jpg

But they only come in 9inch wide - is that too wide for my r32 GTST at the front? - i dont want guard rub :thumbsup:

And would i be able to stretch 215/40/17's on them too?

And lastly, my cars not low at all - so would that aid in being able to fit them?

They are 17x9 - 30 offset

Im not clewed up on mags, so it really is a guessing game for me...

Edited by Flux_nz
Link to comment
https://www.sau.com.au/forums/topic/278546-will-these-mags-fit-my-r32-gtst/
Share on other sites

are you sure it's -30 and not +30?

there is no chance -30 will look anything short of ridiculous, but +30 is achievable.

i wouldn't personally put 215s on there but if you were so inclined you could

+1

9inch +30 with scrub on the rear (if lowered). Will need to roll the guards or have some negative camber.

They will also scrub on the front depending on height.

I had +30 8inch on the front with 235/45 tyres and it would scrub. Dropped to 225 and scrubbing went away. Yours are 1inch wider so would scrub much easier in my opinion.

9inch +30 is the same design as R33 GTR rims. So best to ask any r32 gtst owner with r33 gtr rims and they will tell you a deffinite answer on fitting.

9inch +30 with scrub on the rear (if lowered). Will need to roll the guards or have some negative camber.

They will also scrub on the front depending on height.

I had +30 8inch on the front with 235/45 tyres and it would scrub. Dropped to 225 and scrubbing went away. Yours are 1inch wider so would scrub much easier in my opinion.

9inch +30 is the same design as R33 GTR rims. So best to ask any r32 gtst owner with r33 gtr rims and they will tell you a deffinite answer on fitting.

I have R33 GTR wheels on an R32 gtst with 245/45 rubber, standard-ish ride height with stiffer shocks & springs, i had to get rears rolled (not lipped) and have had no scrubbing what so ever.

Front is a different story..... 245's on the front, standard guards untouched, only when i hit a big dip or bump does it slightly scuff something on the tyre, it hasn't chopped sidewalls (I cannot see any damage what so ever to the tyre's), i use to have a pair of tyre's on the front with worn shoulders and it never scrubbed once over anything.

Tyre's rubbing shouldn't be your main concern, just slap 235's maximum on them and you should be fine with standard-ish ride height. (My 245's stick out front the guards at the front and would probably be deemed unroadworthy, next set of tyres are going to be 235's)

I would worry about the +30 offset rims effecting your roll centre and what it does to your steering & suspension.

+30 changes your roll centre and steering becomes more 'darty' over ruts and divets on the road. (each front wheel wants to roll around bumps instead of travelling up and down over them). This means constant corrections have to be made to keep it going straight. 12 months have past with the wheels on and i have had to replace steering rack bushes from all the extra movement in the rack.

Other bushes at the front have probably been prematurely worn because of the wheels.

They look fat and grip great on the twisties and track but are very compromised on the road.

More solid steering rack bushes at the front have helped quite a bit but I wouldn't recommend +30 offset on a car that has to be driven daily in the city unless you like the steering wheel jumping out of your hands.

Just my 2 cents

I have R33 GTR wheels on an R32 gtst with 245/45 rubber, standard-ish ride height with stiffer shocks & springs, i had to get rears rolled (not lipped) and have had no scrubbing what so ever.

Front is a different story..... 245's on the front, standard guards untouched, only when i hit a big dip or bump does it slightly scuff something on the tyre, it hasn't chopped sidewalls (I cannot see any damage what so ever to the tyre's), i use to have a pair of tyre's on the front with worn shoulders and it never scrubbed once over anything.

Tyre's rubbing shouldn't be your main concern, just slap 235's maximum on them and you should be fine with standard-ish ride height. (My 245's stick out front the guards at the front and would probably be deemed unroadworthy, next set of tyres are going to be 235's)

I would worry about the +30 offset rims effecting your roll centre and what it does to your steering & suspension.

+30 changes your roll centre and steering becomes more 'darty' over ruts and divets on the road. (each front wheel wants to roll around bumps instead of travelling up and down over them). This means constant corrections have to be made to keep it going straight. 12 months have past with the wheels on and i have had to replace steering rack bushes from all the extra movement in the rack.

Other bushes at the front have probably been prematurely worn because of the wheels.

They look fat and grip great on the twisties and track but are very compromised on the road.

More solid steering rack bushes at the front have helped quite a bit but I wouldn't recommend +30 offset on a car that has to be driven daily in the city unless you like the steering wheel jumping out of your hands.

Just my 2 cents

i had the tramlining issue with 235/45's on my +30 rims. Steering wheel would pull into any ruts in the road etc, was annoying to drive with.

However after dropping to 225/45, adjustable camber bushes,adjustable castor bushes and a proper alignment, the tram lining disappeared and have no issues.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
×
×
  • Create New...