Jump to content
SAU Community

Free Compliance For Cube And Civic Ep3

carizma
 Share

Recommended Posts

carizma Community Regular

carizma

Posted
Posted

We currently have 27 vehicles on our compliance list and we are about to add 2 more, Both the Nissan Cube and the Honda Civic EP3.

What we need a Test Vehicle of both types for our compliance testing. The turn around would be 3 to 6 months, but it would be a free compliance. Car of course we have to be clean, no rust and as close to factory condition as possible. It would have to come to Melbourne firstly of course but we could send it off from there.

If you are interested email us at [email protected] or call on 03 9415 7150.

Regards,

Paul @ Carizma

carizma Community Regular

carizma

Posted
  • Author
Posted

The cube needs to be a 1.4 Ltr, Auto up to 12/2005

The Civic EP3 Type R needs to be up till 12/2003

quick question, would it be cube gen 2 or 3? not sure which engine/trans choices are on the possible raws list.
Beer Baron Grand Master

Beer Baron

Posted
Posted

not interested in doing the 04 model EP3s? or did the have the facelift during 03 sometime? I'm keen on one of the later EP3s with the slightly updated front end. just can't remeber off the top of my head if that occurred in 03 or 04 model?

carizma Community Regular

carizma

Posted
  • Author
Posted

Hey Baron,

We will eventually, it would require a new emissions test, so down the track yes but in the short term we are gonna start with up to 12/2003

Paul @ Carizma

not interested in doing the 04 model EP3s? or did the have the facelift during 03 sometime? I'm keen on one of the later EP3s with the slightly updated front end. just can't remeber off the top of my head if that occurred in 03 or 04 model?
Beer Baron Grand Master

Beer Baron

Posted
Posted

cool. so I am right that the facelift EP3 with the different lights/bumper/etc is 04 onwards? I am a long way from being an EP3 expert :P

I might still go for a 02/03. if I find and buy a suitable car I will let you know asap.

thanks Paul.

carizma Community Regular

carizma

Posted
  • Author
Posted

Not sure about the face lift, will find out but the reason were not doing 04 on wards atm is emission testing requirements changed and it got more expensive to test.

Paul @ Carizma

cool. so I am right that the facelift EP3 with the different lights/bumper/etc is 04 onwards? I am a long way from being an EP3 expert :P

I might still go for a 02/03. if I find and buy a suitable car I will let you know asap.

thanks Paul.

Beer Baron Grand Master

Beer Baron

Posted
Posted

yeah fair enough, it makes sense. I think it is 04 when they had the facelight, new lights and front bar and the interior changed a little too with different recaro's etc.

Chris Rogers Grand Master

Chris Rogers

Posted
Posted
That's correct, they are a goer now.

ta!

looks like I need to snatch one for a few more days.

was it heath that cleared it?

remember them saying they had to smash glass on one.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      What should I do next to hold the head on

      By Dose Pipe Sutututu · Posted

      Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • GTSBoy
      boost source Size Garrett gt28 gen2

      By GTSBoy · Posted

      Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Dose Pipe Sutututu
      boost source Size Garrett gt28 gen2

      By Dose Pipe Sutututu · Posted

      Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • oHBoy.
      2001 R34DE

      By oHBoy. · Posted

      3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...