Jump to content
SAU Community

Recommended Posts

  • Replies 41
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

All logic goes out the window in the wet....fark knows how to drive a car quick in the wet :P Especially on slicks, a light car and damp...with a car pulling away in front so you just want to push on and cath him :(

Me? I would have been ff at turn 3 lap 1

The only thing constructive i can say is you either drive the thing mega straight off boost and light throttle openings so as not to slide the thing...OR you just punt the thing sideways on every corner...you are sliding it and anticipating the slide so it doesnt catch you out and also helps throw heat into the tyres ....lol listen to me, it works when i drive go karts in the wet :)

If you're referring to me then don't get me wrong, I'm not having a go at all and I'm sure he is much more experienced and better driver than I am! Apologies if it was taken the wrong way but I did try and clarify with "to each their own", just saying it was a different style to what I'm accustomed. :P

Was there much damage?

Brilliant car. Does it really need a 900hp RB26/30? lol

Unfortunate accident though. It seems he was still on it as he was turning left and the rear end of the car just came around on him under boost. Not much he could have done in that instance.

Do you have any external pics of it?

Edited by SRS13

Fixed :down:

Fark me ... look at those tyres. No wonder it has good traction! :/

How does the little Caterham thingy in the background go? After driving one recently i want to buy one and throw my money away on another car project that I'll never get around to finishing.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...