Jump to content
SAU Community

Recommended Posts

  • Replies 716
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Good to see you got it back all finished.

Did you get it inspected before you picked it up? Did you get your cage paperwork for your log book?

Looks good.

just needs a letter from the welder and to meet cams spec

wont be log booked till the other shit is in

just needs a letter from the welder and to meet cams spec

wont be log booked till the other shit is in

Nice fats but can you still get your arse in to drive it?

sickness bro! I was thinking the same thing as johnny, how you going to recline your fat chair with the X in the main hoop!?! lol.

did you get brad to make some new seat mounts too so you can mount it nice and low so you don't need to drive with your head out the window? you are a big unit.

and yes now I must come give you your diff so you can keep going.

cage looks good btw. i likey.

cage is complete

top job buy brad and well priced, highly recomended

anyway

just have to give it a lick of paint and on to putting the sucker back together

Picture002.jpg

Picture003.jpg

Picture004.jpg

Picture005.jpg

Picture006.jpg

Gday just a quick question about the bar work to the rear wheel arch

i take it that it is still picking up the suspension point?

am humming and harring about if i should carry the back cross thru the back fire wall to the side of the suspension surround is there any point?

no that is nowhere near the rear strut unfortunately. the rear strut top is well into the boot. and the lower arms and diff mount to a subframe with mounting points elsewhere.

pete....pain the cage good. it is impossible to get to later once everything is back in

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Ahhh, I need the whole head unit. I definitely needed to roll back through and review your setup, ha ha! Neat setup they have going on. I just need a full double din head unit. But I want good and responsive. I might have to review what the likes of pioneer have out these days.
    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
×
×
  • Create New...