Jump to content
SAU Community

Recommended Posts

Hi, recently bought a N/A r33. Didn't come with an owners manual.

Just wondering if its ok to run the car with standard unleaded (91 Octane) or will this damage the car?

Filled it with premium (98 Octane) the first few fills and it drank a tank in less than 3 days, and i don't drive like a maniac at high revs either.

Its drinking the standard unleaded much more slowly which is good for the everyday driving i do and cheaper, but i just wanna know if this is ok for the car?

Thanks Justin

Link to comment
https://www.sau.com.au/forums/topic/286403-the-correct-fuel/
Share on other sites

Your car is built for a higher octane (100?). I would use at least 95

E10 is good, its cheap and should hold off those nasty noises - until you start winding up the timing that is. Even better, E85

Do a search for fuel consumption, plenty on here about possible causes i.e. sensors, filters etc.

one of my mates used 91 octane fuel on his skyline and the engine went bang later. higher octane fuel reduces the chances of detonation which is why i only use BP Ultimate 98RON( WA doesnt have Shell optimax grrr :P ) more expensive fuel but better than expensive repairs.

Edited by R33_NICK

I read somewhere that NA skylines were able to run on regular japanese fuel while the turbocharged versions ran on premium. Im pretty sure regular japanese fuel is 89 AKI which equates to around 94 octane so maybe try 95 octane? Keep in mind I know next to nothing about skylines so this may not be true

technically you shouldn't get any real difference in economy from regular to premium. the ecu reads how much air is going into the engine and puts in the set amount of fuel for that afm voltage and tps position. other things will affect economy much greater than the type of fuel. you don't just take into account what revs you are doing, but how far you push the accelerator down. someone flooring it but only reving to 3000rpm will use more fuel than someone who revs to 4000rpm but uses half the throttle percentage. also the O2 sensor controls the fuel economy at light throttle loads, so if that dies your economy goes bad. also if the thermostat is shot and your car takes for ever to come up to operating temp then you will get poor economy as well. or you could simply have a slightly dicky fuel gauge. then there is your driving environment. if you have to stop at traffic lights often then you will get poor economy compared to someone who drove the same trip but got a green light every time.

finally, you said that a tank was lasting you 3 days, but the more important information is: how many kms were you doing in those 3 days, and how many litres are you calling "a tank"? i have used a full tank of fuel in a day, but i also drove 600km on that tank.

finally, you said that a tank was lasting you 3 days, but the more important information is: how many kms were you doing in those 3 days, and how many litres are you calling "a tank"? i have used a full tank of fuel in a day, but i also drove 600km on that tank.

agreed, you could say you used 2 tanks in one day - but if u were driving from brisbane to sydney that would be understandable..

so more info pls?

i would however stick to bp ultimate or mobile 8000 buddy

98ftw :woot:

Edited by astrotristan2

to me if you can afford to own an import / modified car, you can afford to put 98 octane fuel in it at least! It just never ceases to piss me off that though the price for unleaded can vary up to 20cpl, ultimate etc hovers around the 1.38-1.45 mark constantly!

When I had my NA 33, I always put V-Power in it for about 1.5years and I went to sell it, after the buyer has put a deposit down, I just put in cheap normal unleaded.

And straight away, I could notice the difference, the car's responce is so much more laggy.

As for mileage, I find putting 98 in, can get me more k's than normal unleaded.

  • 3 months later...
to me if you can afford to own an import / modified car, you can afford to put 98 octane fuel in it at least! It just never ceases to piss me off that though the price for unleaded can vary up to 20cpl, ultimate etc hovers around the 1.38-1.45 mark constantly!

Like he said, if you can afford modified car u can afford 98 octane fuel

Shell V-Power ftw

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...