Jump to content
SAU Community

Recommended Posts

i have a r33 s2 auto and have changed the turbo over to a hypergear hyflowed turbo. when it gets on boost above 6psi it sounds like a huge whistling sound coming from it ?????? Mods so far are fmic,full 3" exhaust split fire coils and a turb o smart boost tee. I have cheched the gaskets and intercooler pipes and have got no leaks anywhere. This has become a bit of a problem some times because that is all you can here when it gets a bit of psi. does anyone else have this problem or is it normal??

Link to comment
https://www.sau.com.au/forums/topic/287660-whistling-turbo/
Share on other sites

If it turns on to grinding noise it means bearing failure that causing wheels to eat in to housing. Normally due to oil contamination, insufficient oil pressure or flow.

Normally BB turbos give that sort of noise before failing.

Check for vacuum leaks.

Link to comment
https://www.sau.com.au/forums/topic/287660-whistling-turbo/#findComment-4822753
Share on other sites

hmmm...not sounding good....although it is reason to buy a new one...was running fine tonight...in the cool air n all too...drove into city was coming home give it some stick and ...arrrgghhhhhhh....wtf is that noise...gradually got worse

I'm not exactly sure what turbo it is...I've seen standard ones and its not the same...

but rebuild or replace whats the best option

assuming its the problem

Link to comment
https://www.sau.com.au/forums/topic/287660-whistling-turbo/#findComment-4822760
Share on other sites

Well there are 2x sorts of noises. one is a howling sound. This is common to BB turbos, and it gets very loud from time to time, then you have fins rubbing housings making a grinding noise, turbo stops function. You also get a small grinding alike bearing noise when power off your engine. If this is the case then the turbo needs to be taken out and looked at.

The other sound is a high pitch whistling sound. This is generally due to air pass though a small gap. could be a leaking pipe, or any gaskets on the intake system.

Link to comment
https://www.sau.com.au/forums/topic/287660-whistling-turbo/#findComment-4823048
Share on other sites

this noise is kind of like the noise a loose fanbelt makes on start-up...but alot worse..

started around moorabin ,by the time i got near frankston it was getting much worse

but only noticable with heavy throttle applied. driven normally seems fine

..hmm just took a quik spin around the block seems fine..but didnt get a chance to mash the pedal...maybe try an oil flush..is motul 3100...ok?

Edited by doozooby
Link to comment
https://www.sau.com.au/forums/topic/287660-whistling-turbo/#findComment-4823140
Share on other sites

i have replaced all the hose clamps and silicone hose's,all the vacum hoses and have checked the gaskets and nothi ng is leaking. Oil is changed every 5k. it makes constant boost and is not loosing power. this turbo has always made this sound and now i have just got to a point were it is starting to piss me off. the turbo has only done 20k. help

Link to comment
https://www.sau.com.au/forums/topic/287660-whistling-turbo/#findComment-4823321
Share on other sites

Hmm sounds like an air leak to me. I had this problem for a while with my hypergear turbo, Check your 4 manifold studs.. see if there tight.. check for anything loose , cooler piping and all. if not then it has to be oil starvation, did you change your oil feed line and bolt? because nissan come stock with an oil restriction... on the bolts..

Link to comment
https://www.sau.com.au/forums/topic/287660-whistling-turbo/#findComment-4826765
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even with the piston at TDC there was room for it to drop, but I don't think it can drop fully into the cylinder, the problem you have is that you need something pushing against the valve to hold it up so you have enough room to put the new stem seal on and the spring etc.  I used compressed air only because putting rope in the cylinder seemed a bit risky to me, I know people have done it countless times before like this. Overall it's a pain in the ass job. Honestly you'd probably be better off taking the head off because the risk of dropping something in the engine and the finicky-ness of it all is very stressful. If you are going to attempt it though i 10000% recommend a 36050 valve spring/keeper tool. I had both the traditional lever type and after doing 1 cylinder it was absolute pain to get those valve keepers in place, even with 2 people. That 36050 is amazing, you do have to push hard to get them in place but it works perfectly almost every time. Back to my actual issue I think my engine is just tired and old and the rings have gone bad. The comp numbers (cold, no oil) were: Cyl 1 -129psi Cyl 2 - 133psi Cyl 3 - 138psi Cyl 4 - 137psi Cyl 5 - 157psi Cyl 6 - 142psi   Cylinder 5 and 6 having the most carbon on them.
    • Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
×
×
  • Create New...