Jump to content
SAU Community

Recommended Posts

mines bashed out , i got i tuned when it was bashed out, it sounded a bit louder and gained mayb a little tiny bit of kws but its not worth having an EPA and stuff like that. Im gona chuck on back my CATCO highflow cat.

when dyno tuning and dyno running, better without cat, this will deliver a more accurate A/F ratio as all tuners run the WB O2 using an exhaust sniffer rather than mounting it in the dump, pre cat where the cat doesn't affect the reading.

And yes, more power, with cats, once they're hot they become a restriction.

No cat is better, can run a straight pipe with the stock cat plate welded on so no1 notices; simply swap to compliance cat if you need an EPA. A regular RWC mechanic wont notice it either.

if you are paranoid n wanna play it right, seems those 5inch body high flow metal cats are the answer; not cheap though. Probably wont pass EPA either so better jst run the straight pipe n swap it to compliance when u need to get tested.....enjoy the flames also lolz

Hey sorry to hijack this thread a bit but what sort of power gain do you think i would see converting from a standard cat (2.5 inch inlet / outlet modified to fit 3 inch) to a highflow cat? Note I currently have a full split dump / front pipe which is 3' and the rest of the exhaust (excluding cat) is 3' aswell.

I had no cat for a while, couldnt stand the fumes, headache material.

I put a Metal Cat 3.5 inch 100 cell cat back into my system and I love it. The horrible fumes are gone. The exhaust no longer stinks out the garage and I lost zero power when it went in. Response even improved when it went in and ECU got retuned.

Hey sorry to hijack this thread a bit but what sort of power gain do you think i would see converting from a standard cat (2.5 inch inlet / outlet modified to fit 3 inch) to a highflow cat? Note I currently have a full split dump / front pipe which is 3' and the rest of the exhaust (excluding cat) is 3' aswell.

a fair bit. cat is the biggest restriction in your exhaust, then dump, and lastly catback. you've gone about it backwards like i did.

a fair bit. cat is the biggest restriction in your exhaust, then dump, and lastly catback. you've gone about it backwards like i did.

Yeh bought it from a guy who said it was a catless system... Got home bolted it up n realised there was a gap which matched where the cat would be :cool:

So yeh just on the cheap atm... so am waiting for one to come up.

  • 2 weeks later...

depending on what state you are in, the fine for not having a catalytic converter on a street car can be up to $10,000.

if your chasing 1 or 2kw by running a decat pipe, is it really worth the fine? if u want to make more power, dont f**k around with cats, get your engine built, better turbo, deacent ecu, and a good tune.

depending on what state you are in, the fine for not having a catalytic converter on a street car can be up to $10,000.

if your chasing 1 or 2kw by running a decat pipe, is it really worth the fine? if u want to make more power, dont f**k around with cats, get your engine built, better turbo, deacent ecu, and a good tune.

+1

Also with decat/bashed cats, on a white car you get brown stains/marks on the rear bar.

but. the flames?

seriously though its not worth it ey, if all you get out of it is some flames and a non-noticable power increase.

if you got the car with an exhaust already wouldnt bother stuffin around man, if it were completely stock on the other hand, would get a whole new turbo back.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm actually not sure - I think it was "Stealth Performance" (It really is near impossible to find a FEMALE 1/8BSPT to 1/8NPT male at ALL) but having the thing leveraged on a 90 degree angle on a small aluminium fitting is not too smart. Also in not too smart, I've drilled out the center of the broken fitting so there's maybe 0.00001mm of thread to bite into, so yeah. I may have to get it drilled/tapped/plugged entirely. Given I could conceivably tap a thread/adapter/pressure line in any point in the oil system I suppose it's feasible to run a line to the Nissan Sensor to keep the dash working. Do these exist in AN fittings and the like? Like an AN fitting that has a NPT (or other?) thread as well for putting a sensor in?
    • I would agree.  There will be an amount of boost you could run safely with an otherwise factory system, but it would be low enough to not be worth the cost.  And if you are reliving your 20s, you know a 'little bit' was never enough. Personally, if I didn't want to spend the money, then stick with NA bolt-ons, and maybe a tune.
    • Fuark, at least the motor survived. What brand was the fitting that snapped?
    • Wrong question. There's no point in spending the rather large sum of cash and effort to add turbo, without taking it to the "sensible" limit of the motor itself. If you have to upgrade injectors, etc, then so be it. That is a tiny fraction of what it will cost you to turbo it.
    • Measure voltage at the starter solenoid terminal when the key is at start and it has clicked. If it is really low, then the suspicion falls on the ignition switch (contacts or wiring thereof) as causing a voltage drop instead of sending enough volts to throw the solenoid all the way to engage the starter itself. If it is a decent voltage, then the suspicion is on the solenoid. Might have s horted coil, or might hva dirty contacts. Rip the starter off, dismantle, clean up contacts and inspect winding. It might not be possible to see if there is a short in the winding though. I have a spare starter here that I could measure the resistance of the coil, as a guide to about what it should be, if you need a comparison. <parts hoarder>No you cannot have it.</parts hoarder>
×
×
  • Create New...