Jump to content
SAU Community

Recommended Posts

Anyone interested might like to pick up a copy. Entertaining reading. Apparently all cars have been modded, some seriously (however the GTR ran basically stock times at the 1/4 mile, despite being tuned...). They ran some laps of Oran Park too... The GTR was beaten by the GT2 and Porsche by 0.5s and 0.2s respectively. The thing is, the GT2 was running hoosier r6's (basically slicks) and the Turbo was runninng Formula R Toyos. The GTR was running the OEM Bridgestones.... Why you would install $50k in mods and then run standard bridgestones isnt quite reality (if you're seriously interested in lap times that is). i know for a fact that the bridgestones are 2 seconds slower than r-specs on the GP circuit, which would easily translate into 1 second on south. Anyway, interesting reading nonetheless, but i reckon the GTR would have easily beaten the South times with equivilent tyres. In fact, i reckon even a standard GTR would have kicked the modded GT2 and Turbo's arses collectively, given the same tyres. Amazing really, given the price!

Edited by LSX-438
Link to comment
https://www.sau.com.au/forums/topic/288705-motor-magazine-extreme-tuners/
Share on other sites

I had just a quick flick through at the shop and noticed the power output listed of the "modified" GT-R... 258awkW estimated.

Don't they come with near 300awkW as standard? What are they doing?? :)

That car would've had somewhere approaching 345 at the wheels. They must have had Dyno dramas with it and stuffed up the estimate. I was surprised how slow it was given these mods. White 35 has 345 at the wheels and is pulling 3.3 0 - 100. Duncan did a 11.1 quarter mile in his with similar mods. My Mods were also a lot cheaper, and produced much better results also.

Maybe they babied the car, or it was hot, or boost was turned low...or something.

It says somewhere in the article they had dramas removing the carbon undertray which meant they couldnt dyno the car, probably due to clearance issues (or maybe they didnt want to get it dirty, lol). Maybe it has an aftermarket undertray? anyway i removed my complete undertray in my garage with $2 tools, so dunno what's up with that. And yeah it should have about 340awkw. Their estimates are a bit rubbery. Interesting article though.

I have the mag,

Reasons for slow times are due to the owner not letting them use launch control and as mentioned above stock rubber.

Hardly seems worth while entering a car in that type of comp then saying no to using all the gizmos on the car like launch control.

FYI check out the Golf R32 that city performance entered, $70k in mods, bloody crazy.

Yeah, that guy's letter in the August issue (Porshe choice) got me fired up & thought

I would say something! They always cut down the text though & made it read a bit nicer

than what I put down - haha. I suppose the response was that they printed it (my 2nd time)

Its a shame Willall couldnt get the Silver R35 with the Turbo upgrade in that shootout -

that would have been quite interesting. Nice body parts & all the internal goodies as well.

Yes it was a good article. Motor have been doing lots of "tuner" articles over the last few

years & it is the only magazine I buy regularly.

I agree about the launch - whats the point in putting it in but saying dont go for it?

Surely one or two full launches wont hurt it ( ah hem.. I have done a few with my full

JDM launch control with no problems)

I have the mag,

Reasons for slow times are due to the owner not letting them use launch control and as mentioned above stock rubber.

Hardly seems worth while entering a car in that type of comp then saying no to using all the gizmos on the car like launch control.

FYI check out the Golf R32 that city performance entered, $70k in mods, bloody crazy.

Overly careful owners like that does not help the erroneous belief being passed around by GTR 'haters' that the GTR's transmission is 'fragile'

Surely one LC will not hurt the transmission - especially when it's the revised LC where warranty is not void so long as VDC is not turned off. :ninja:

I had just a quick flick through at the shop and noticed the power output listed of the "modified" GT-R... 258awkW estimated.

Don't they come with near 300awkW as standard? What are they doing?? :)

From my memory of that article their estimates were based on a 30% drivetrain loss.....which sounds unusually high...obviously resulting in the lower rwks.

Willall just dynoed my R35 JDM on their 4 wheel dyno & it made 278 awkw standard.

Now waiting for results from new custom COBB tune with boost control. It is not unusual

for cars to vary on power level depending on kays & type of dyno used.

Willall just dynoed my R35 JDM on their 4 wheel dyno & it made 278 awkw standard.

Now waiting for results from new custom COBB tune with boost control. It is not unusual

for cars to vary on power level depending on kays & type of dyno used.

what was the boost level?

  • 1 month later...

Some of you may remember this shootout. An R35, with apparently $50k in mods, ran a 46.7 around Oran Park South. It was running the stocker bridgestone tyres. I think it was John Bowe driving. Compared to a 911T running 888's (46.5) and a GT2 running Hoosier A6's - which are essentially slicks, running the best time of 46.2.... ALL cars had various mods. The tyre thing gave me the shits though (i mean really, a GT2 on slicks vs an R35 on stocker bridgestones).

Anyway, i had a chance to run Oran Park South in my R35 with slicks recently....

Result=46.3

Now, i dont have $50k in mods, and i am not John Bowe. I have less than $10k in mods (Willall midpipe, tune, 18" wheels and tyres). In fact, it's about $5k really, as i was using cheapie 2nd hand slicks on the day. Michelin p-cup 270/68/18's.

What does this tell us?

a) The GTR is one awesome machine, proven capable and comparable to the 911T and GT2 at a fraction of the cost.

b) You dont need to spend $50k on mods, in fact you'll probably make it go slower (if done merely for bling factor)

c) For track excursions, the No.1 most important mod is... TYRES.

Edited by LSX-438
Some of you may remember this shootout. An R35, with apparently $50k in mods, ran a 46.7 around Oran Park South. It was running the stocker bridgestone tyres. I think it was John Bowe driving. Compared to a 911T running 888's (46.5) and a GT2 running Hoosier A6's - which are essentially slicks, running the best time of 46.2.... ALL cars had various mods. The tyre thing gave me the shits though (i mean really, a GT2 on slicks vs an R35 on stocker bridgestones).

Anyway, i had a chance to run Oran Park South in my R35 with slicks recently....

Result=46.3

Now, i dont have $50k in mods, and i am not John Bowe. I have less than $10k in mods (Willall midpipe, tune, 18" wheels and tyres). In fact, it's about $5k really, as i was using cheapie 2nd hand slicks on the day. Michelin p-cup 270/68/18's.

What does this tell us?

a) The GTR is one awesome machine, proven capable and comparable to the 911T and GT2 at a fraction of the cost.

b) You dont need to spend $50k on mods, in fact you'll probably make it go slower (if done merely for bling factor)

c) For track excursions, the No.1 most important mod is... TYRES.

Agreed, in fact I have 19 inch Volks on the way wrapped in Hoosiers - look out Bathurst a two twenty something is in my sights...

  • 2 weeks later...
  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
    • The video for the servicing and fuel filter change can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44 One of the main jobs I wanted to do before the car officially went on the road, was to remove the awful looking blue silicone hoses. There's nothing wrong with having coloured silicone hoses, but I realise as I'm getting older I prefer monotone engine bays with a splash of colour on the engine cover(s). I cover this in a lot more detail in the Youtube video, so unfortunately there's limited photos of the process. The intercooler, upper radiator, boost vacuum and upper breather hoses were all changed to black silicone with mikalor clamps. The only blue left is a blanking cap at the back of the inlet manifold and the GReddy pulleys (which will be replaced for stock when the cambelt gets replaced) While the intercooler pipes were off I gave them a quick clean/polish too A before photo I do have a replacement air filter on its way. Fuse box covers were painted blue, they're now satin black Another job on the list while the bumper was off, is to add some mesh https://live.staticflickr.com/65535/54737966256_99b28bfa30_c.jpg[/img] I was hoping to use some thin wire to secure it, but it seems I've misplaced it and the wire I had was too thick to twist easily. I ended up using cable ties for the time being https://live.staticflickr.com/65535/54737131882_c2b7989dcc_c.jpg[/img] Was pleasant to see this https://live.staticflickr.com/65535/54737131627_8b2aab13b3_c.jpg[/img] The last thing to do was to fix the front grill and re-mesh that to match but I ran out of time The Youtube video can be seen here: https://www.youtube.com/watch?v=R4FsF6tgizE&t=23s
×
×
  • Create New...