Jump to content
SAU Community

Recommended Posts

Ando,,,you say the tyres are 99% new,,,that tells me either you or someone else has done the nice and easy heat cycle laps. Either way whats done is done and now just go out and thrash the living shit out of them.

Neil.

  • Replies 40
  • Created
  • Last Reply

Top Posters In This Topic

Everytime i'm at Gordon Leven's he talks me out of full slicks (for my little car) because as duncan said they will go off and lose grip before you wear them out. The constant heat cycles of our trackday sessions is worse than just throwing them on and driving non stop till they are down to the wear markers.

Also, he has most sizes of semi + slicks for under $100 used (by used I mean 1 trackday or 1 supersprint event).

Dude!!!!! Hook me up!!!!!!

What do you need slicks for Baron I havent seen you at any of our events for a couple of years :P

just cause you haven't seen me doesn't mean I haven't been out there. driven R35 at oran GP and PI just this year, throw a few other fancy ones in there too inc a ford GT. ran the silvia at PI last year an OP as well. did eastern creek about 6 months ago too... is that enough? :)

Everytime i'm at Gordon Leven's he talks me out of full slicks (for my little car) because as duncan said they will go off and lose grip before you wear them out. The constant heat cycles of our trackday sessions is worse than just throwing them on and driving non stop till they are down to the wear markers.

Also, he has most sizes of semi + slicks for under $100 used (by used I mean 1 trackday or 1 supersprint event).

I have not seem him with any GOOD used tyres in 235/245 or 255 17s for a long time. and his prices just kept going up and up for tyres he gets for free. 5 years ago he used to have good tyres. but i haven't seen any decent stuff in 17inch there for a looong time, and most he did have were badly heat cycled A048s.

out of interest I just rang him. he has nothing in 16s at all. and in 17s has just one set which is $400 for a set of used cum-hos 235/40/17... he may have lots of stuff in small sizes but his stock and prices on used 17s and 16s hasn't been good for years. obviously stock goes up and down, but years ago when no-one wanted the stuff his prices were not bad and sometimes he actually did have good stuff but these days most of the stuff is long past it's best heat cycle wise even though they may still have tread and for what you're getting it's not good value. well at least not in 16/16/18 inch sizes.

anyway, back to the topic at hand. those 205/16s would go very nicely on a GTI-R pulsar, or a integra Type R (they may come with 17s standard though), MX5 perfect (looks at Chris), most models of Civic (and there are plenty of hot ones at the track these days), check out forums like that and you may find a home, or chuck them on ebay. could be a winner there. :P

check the build date stamped on the sidewall before you use them. Not sure when Falken last made slicks...

its the last 4 numbers of a code stamped into the sidewall. first 2 of them are the week number and the last 2 digits are the year. I wouldn't bother with them if they're more than 3 years old.

the kumhos in 235/40/17 for 400 are an excellent buy. they are our new control tyres, I run 245/40/17, they are 1300 a set new, wear very well and are within 1/2 sec of the dunlops and bridgestone. far better than the crappy yokos.

the kumhos in 235/40/17 for 400 are an excellent buy. they are our new control tyres, I run 245/40/17, they are 1300 a set new, wear very well and are within 1/2 sec of the dunlops and bridgestone. far better than the crappy yokos.

$1300 a set is a great price considering RE's are not up at near on 2k, as are the AO50's. Which ones are they Duncan?

Are you refering to a treaded tyre Duncan?

I am going to get slicks, anyone have any feedback on a brand they'd recommend?

And I'll ask the question again, do you agree I'll get more life per dollar on slicks?

I have a set of brand new Hoosier slicks for my car build. They are a not too expensive and the distributor is in NSW

MAybe look into those if you want a reasonable set at a good price.

http://www.hoosiertireaustralia.com.au/

A few mates and I are also running the Kuhmo V70A/V700 245/40/17. Picked them up from John Mills at F-Sport for $330 each as they are the control tyre for the Saloon car series. For $1320 for a full set, you cant go wrong. Will be buying another set whilst they are at this price. The 235 and 255 sizes are up around $470 mark as they are not the control tyres.

Edited by SRS13

Yeah they go OK. The size is fine as it fits both 8" & 9" rims well.

Managed a 1:20.06 at Oran GP with them on the weekend. Grip levels are good and the wear seems to be OK. Going to Wakefield this Monday so will see how they go at a track I am familiar with.

Can't compare them directly to a RE55 as I have not used the RE55's brand new.

My thoughts on the Kuhmo's so far.

The sidewall is stiff being only a 40 profile so tyre roll (sidewall flex) isn't that great as compared to an RE55. As such, you dont need to run as much camber as you would with the RE55. I am finding that whilst the wear is good (longevity) the wear is slightly uneven across the tyre. The inside is wearing more than the outside which suggested that I may be running too much camber. I backed off the camber when getting a wheel alignment from 4deg front and 3deg rear to 3deg front and 2deg rear. Even then, the wear is slightly uneven wearing more on the inside than outside. Not sure if this is to do with my set-up or the tyres however I remember the old Lotus cup tyres (205/45/16) wearing in a similar manner. Grip levels mid corner and corner exit were slightly reduced with the reduced camber but thats a trade off for increased tyre life I guess.

The Kuhmo's are rated as a hard compound so you can go quite a few laps without them going off. They get up to heat pretty quickly though (1-2 laps) but maintain grip levels for up to 10 laps. The Kuhmo's like slightly higher tyre pressures. I ran them on 30 cold and tried to keep them at around 34-36 hot as recommended by Kuhmo, whereas with the RE55's I ran them 32 hot. So far I am happy with them except for the uneven wear however if I had the same size rim all round I could have rotated them to assist with the wear.

Will let you know how I go at Wakefield. 1:07.xx is the target....

Awesome, thanks for the detailed write up.

I run the same size rims all round so rotating is not an issue, so I'm keen to see how they perform and how long they last for. RE prices are just crazy now so a cheaper alternative would be very tempting. I'm not so sure 245's would clear at the front for me though which would be my only concern.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Apologies for the long post, but needed somewhere to lay out the entire timeline of events and actions taken:   I've got an 89 GTR with a R34 RB in it. It's been running great all year, driven probably 500KM in the last month. It's not my daily driver, just a weekend fun car.    Build info: R34 RB26 - HKS 2.7 stroker kit, HKS adjustable cam gears, HKS turbo upgrades, Trust intercooler, R34 factory DENSO 440cc injectors, JUN chipped/tuned R32 ECU. All of this work was performed in Japan back in 2019.    Thursday 10/2/25 - It's a nice day and decided I'll drive it to work, I start it up in the garage and I notice it took a few extra cranks and sounded a bit funny. I figure maybe it was just because it was a pretty chilly morning. I pull it out into the driveway to warm up a bit before leaving. As I leave the driveway, it feels very off and sounds like a misfire. I pull it back in the garage to deal with after work and take the daily to work. I was able to diagnose it as a cylinder 5 misfire with the old spark plug test (unplugging each plug until a sound change with the engine running). I take off the whole ignition system, ignitor, plugs, spark. *Important note, it is still on the R32 ignition system with the separate ignitor system. I test each system with a multi-meter and nothing presents as a smoking gun. I put it all back together and it starts up no issue. I go ahead and order the PRP R35 ignition conversion kit. It should arrive today (10/13/25)   Friday 10/3/25 - Another nice day, car starts up great and drives great all day. Very pleased that everything seems to be OK   Sunday 10/5/25 - Decided I'll take it to play some golf, load up and drive to the course about 25 minutes away. Drives wonderful the whole way there, I pull in the parking lot and the engine completely comes to a stop. I do not recall if it sputtered at all, but just remember all of the sudden the engine was off. I roll it into a parking spot, try to crank it back on and nothing.  It'll crank and crank and not even try to start. End up getting it towed back to my house and push it up into the garage.    Items I have checked: Fuel in the tank Fuel Pump relay Fuel pump fuse  Spark Plugs & gap Coil packs Ignitor    I know the cylinders are getting fuel as the plugs smell like fuel after a start attempt. I tried spraying starter fluid into the manifold and cranking and not even a sputter.    I decided to do the live CAS test (removing the the CAS, ignition on and spinning the CAS stalk to see if the injectors pulse and spark is active). All of the injectors were pulsing and I have spark at the plug. The half-moon end of the CAS did seem very loose, I'm not sure how much play is supposed to be there, but it was more than I expected. There was no in/out play of the shaft, just the tip end that is pinned on had quite a bit of play.    CAS Play video   When I put the CAS back in, I stupidly did not re-time the engine. I know I need to do that tonight, however, I do not think it will start given it seemingly was not the issue. My plan is to do the PRP R35 coil kit and retime the engine at the same time.    I plan on ordering the Haltech Nexus Plug-in ECU once they are available again, but ideally would like to get this sorted before firing the parts cannon at it and potentially adding more variables.    Anything glaring that I am missing here, I'm a bit at a loss?          
    • Get it on a dyno. Get something logging Consult. Run it up and find out what is causing it.
    • Looking for a plenum for rb25 de+t neo  Not looking to push much power maybe 300kw at the wheels, is there much difference in flow for Freddy “Greddy style” compared to original Greddy or options like Proflow or Otaku garage?    I won’t be porting the de Neo head for now as I think it’ll be fine 280-300rwkw but appreciate the help and any experiences anyone has between them and any advice. Thanks  Looking at this plenum for now below 
    • engine wise almost no mods: stock ecu Greddy front mount intercooler Greddy forward facing intake w R33 TB stock fuel system, stock injectors, rail etc. Kakimoto racing hyper 3 inch exhaust system Apexi intake filter New NGK –R BCPRES (.8 gap) plugs  
    • Nice one @Pac - looks like a fair few 1600's there! 
×
×
  • Create New...