Jump to content
SAU Community

Bosch 040 Just Got More Noisy!?!

Yeedogga

By Yeedogga,
in Engines & Forced Induction

 Share

Recommended Posts

Yeedogga Experienced

Yeedogga

Posted
Posted (edited)

Hi guys,

I put an 040 in the car a few months ago. Ran fresh wiring, new relay etc etc

Up until today, you could just hear it humming/sucking away. From inside the car you could just hear over the exhaust & from the outside you could barely hear the pump at all.

Today it has started whining/buzzing and it is significantly louder than normal. Should I be worried?

Edited by Yeedogga
Link to comment
https://www.sau.com.au/forums/topic/289920-bosch-040-just-got-more-noisy/
Share on other sites
turael Enthusiast

turael

Posted
Posted

if it makes you feel better, my 040 makes a hell of a lot of noise, all the time. gurgles, buzzes, whining...

very noisy pump. car has always been fine though, been running it for a year or two now.

Parag0n Mentor

Parag0n

Posted
Posted
I don't have a gauge so I haven't been able to tell. Car seems to be running fine though.

Mate go get an autometer gauge that you can put in your engine bay they're like $20 and hook it up to your regulator, its such a cheap mod for important information if you're running more than base fuel pressure.

femno Grand Master

femno

Posted
Posted

Check your tank for shit!

Pull the pump out and inspect it for black dusty crap on the bottom. If that or anything else is on the strainer of the pump you need to remove the tank and have it cleaned.

James_03 Mentor

James_03

Posted
Posted

My 044 went this way too, exact same symtoms. Started also getting fluctuating pressure.

Ripped it out and went a 023, still never figured out why it died. Was a genuine 044 too, strainer was clean, good wiring etc.

There just getting so hit/miss now it's not funny.

bubba Grand Master

bubba

Posted
Posted (edited)

I really don't think it's anything to worry about, my 044 has been like this for a couple of years now with no issues what-so-ever.

My guess as to WHY is that it's probably working harder to pump the thinner hotter fuel around. It's basically because there is excess fuel travelling to a hot engine bay and back. Standard, our cars run a control module that drops voltage to the fuel pump at idle, these tend to get removed when aftermarket fuel pumps go in.

Edited by bubba
Mayuri Krab Grand Master

Mayuri Krab

Posted
Posted
if it makes you feel better, my 040 makes a hell of a lot of noise, all the time. gurgles, buzzes, whining...

very noisy pump. car has always been fine though, been running it for a year or two now.

Same with mine. Mine has a very loud buzz & grgule sound since day 1 of getting it installed when my stock one died. The exhaust noise covers the pump noise up inside the car, however outside its very noticeable when you are near the rear of the car.

Being fine for about close to a year now.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...