Jump to content
SAU Community

Recommended Posts

I'm really digging the radiator set up... hope it works well for you.

Most people can't appreciate the time and skill it takes to produce neat wiring solutions. Just make sure you are using the correct style of deutsch plug crimps for the pins and sockets.

It's comming along gear guns.

PS... I had my first proper day out sliding (Baskervill) last weekend.. was a blast! I can see how it becomes a destructive addiction.

That's beautiful... Your wiring is just outstanding, really makes me want to strip my car and do everything custom. Because having your indicators on a switch panel in a street car is completely necessary :P

Seriously though, I'm loving this build. I just tend to just sit on the side lines and applaud quietly.

got less then a week to finish this thing for Round 1 ADGP and its going to be an untested car/set up :( oh well see how it goes.

anyway heres todays efforts... im wrecked. ive spent all my time either at work or working on the car, sleep is rare.

mock up of fuse/relay panel.. then a power up to test all circuits.. passed with flying colours!

1239956_555067404542367_2093884917_n.jpg

made up swirl/fill pot for the rad, this is the highest point in cooling system,

1240304_555067431209031_609021108_n.jpg

1044488_555067444542363_979633481_n.jpg

sealed off the floor holes

1235196_555067457875695_1837795553_n.jpg

epic switch panel! LEDs are green and have bright/dim circuit, interior light, etc heaps of neat touches

1377050_555067491209025_687954730_n.jpg

Nice work, I love it!

.... just one thing... you might need to re-orientate the ewp. the way you have it, there will be an air pocket trapped on the back of the impeller, causing it to cavitation and create more air bubbles.

today we had the rad back out cause we found a leak in one of the end tanks. put it all back in and then bled it up. we vacuum filled it and that worked mint. in total it took an hour to fill and bleed and took 20L of coolant. we ran the EWP constantly while it was full and kept adding water in the funnel until no more air bubbles came out. EWP works mint and no cavitation was heard at all. the EWP is mounted lower then the bleed point.

fuel system all done. hard lines from boot to fire wall with bulkhead fittings then braided line in engine bay to connect it all. clean. effective and out of harms way. nothing at all to get damaged on ripple strips etc.

just means the cabin is getting awfully full haha

1385239_555922751123499_883829353_n.jpg

the red things are buttons to scroll through the dash since there are 4 pages. you can also use them to change brightness of dash and various other simple functions.

the leb spec shift light can be set up to come up for any warning light. EG oil press, too hot etc.

got it running last night... after a massive fuel leak. turns out the tank had a hole in it. So swapped a tank out of a 33 4 door and bolted that in... no 5 min job but had to be done. then we put fuel back in it and started the steps to get it running. lots of setting up and calibrating of sensors etc. then it fired straight up and settled into a dead smooth idle.

warmed it up to 80 degrees using the pump on 30% flow, then we turned the fan on 100% and it dropped down to 55 degrees lol.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
    • 310mm rotors will be avilable from Australia, Japan, and probably a few other places. Nothing for the front can be put on the back.
    • The filter only filters down to a specific size. Add to that, the filter is AFTER the pump. So it means everything starts breaking your pump even if its being filtered out.
×
×
  • Create New...