Jump to content
SAU Community

Tcs Switch Not Working On R34 Gtt

Flecher

By Flecher,
in Engines & Forced Induction

 Share

Recommended Posts

Flecher Enthusiast

Flecher

Posted
Posted

hi guys, my tcs switch doesn't work, when i press the switch it doesn't turn off the TCS.

I just got my car back from mechanic as my car couldn't start guess some sensor broke down. The mechanic rewire sth so it could start but then when i push the TCS button the TSC OFF light is not showing up on the dash. I wonder what's wrong with it.

Also, i got this TCS off , SLIP and Engine warning light on and the engine seem to crank and keep misfiring. But when i turn off the car and start again they gone again. I wonder what's the problem? Is sth wrong with the coilpack? as i feel the engine cranks so much n keep misfiring when those light on.

Need advise from everyone. THanks!

Link to comment
https://www.sau.com.au/forums/topic/291217-tcs-switch-not-working-on-r34-gtt/
Share on other sites
Flecher Enthusiast

Flecher

Posted
  • Author
Posted
rewired what exactly? i cant think of anything needing re wiring to fix a break down on a 34. what was the cause of the breakdown...

because my mate's car got smashed at the front and cause has not spark to start up his car. When he turned on the car the engine just cranking and no spark to start it. Therefore the mechanic rewire sth to make it start. Perhaps i should get him to talk to mechanic.

  • 2 months later...
Marcus89 Proficient

Marcus89

Posted
Posted (edited)

I do not think my TCS switch is working in my car either. Although mine hasn't had any rewiring done or anything. From reading this thread looks like there is a fuse so I'll go check all that now.

One question i have is how is the TCS Off switch meant to work do you just start the car and press the switch and then TCS off will come up on the display?

Also is the switch meant to be like a light switch wear you flick it and it stays there or like spring loaded kind of switch wear you press it and then it comes goes back to it's original position after pressing? Just asking as mine is like the spring loaded kind of switch

Edited by Marcus89

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • nouveau_poor
      Unknown sound similar to BOV on positive boost with partial throttle RB26

      By nouveau_poor · Posted

      I certainly fall into the annoyed camp, but glad to hear that if it's happening at low boost then I'm not likely going to blow a turbo and end up with metal shards in my oil. Just feels like it prevents me from really driving it without hesitation and "peak" performance. Wonder if it's the VCAM, it did an impressive job of shifting the torque curve and faster spool, but maybe now it's "too fast" and there's too much air for how open the throttle is.  Based on some other threads, will also do some reading on synchronizing the actuators. They are the default actuators that come on the Garrett's and I would think they would be set the same coming from the factory, but if the turbos don't actually work exactly the same way at the same time as previously mentioned, it would be worth making sure the actuators are actuating together properly
    • GoHashiriya
      R34 Skyline Sunroof Won't Tilt/Vent

      By GoHashiriya · Posted

      I went down this rabbit hole before, ended up sourcing a motor from the UK (I'm in Japan) which also didn't function correctly. With the original motor, I disassembled it and reassembled it and it works somewhat, sometimes. What I could deduce from all my screwing around is that there is calibration of the gears on the inside of the motor and two ramps on the main gear which activate switches that operate the motor and move the sunroof either to retract into the roof or tilt. Where I got stuck was that, it seemed in my case that one or both of the switches that are activated by the ramp on the gear did not always activate and thus the motor did not move, causing it to sometimes not retract or tilt (apologies, I've forgotten which way it didn't work.).  Of course this part is discontinued at Nissan now, it's the same part in the S15 but no other models. I also contacted the manufacturer of the component for schematics - forgot the name, they're based in Gifu - but they declined to share the information due to being bound by an NDA, sadly. Looking through my pictures now, it seems I last had a crack at this in 2022. See, I so kindly wrote "open" and "close" next to the switches. If you figure it out, please do tell me. Those little switches, with the red buttons may need to be replaced.
    • GTSBoy
      R34 Skyline Sunroof Won't Tilt/Vent

      By GTSBoy · Posted

      Something's broken.
    • PranK
      Shoota's R33 GT-R RB30/26

      By PranK · Posted

      It says 300ZX, does that make it an Aus delivered car? Funny how back in the day I just couldn't care less about Z32's and these days I am just in love with them. Back when Nissan was into pushing the envelope. 🤣
    • ShezzDogs
      R34 Skyline Sunroof Won't Tilt/Vent

      By ShezzDogs · Posted

      Hi guys, just after some guidance with an R34 sunroof that has stopped working correctly. It still opens and closes perfectly fine, but it no longer tilts/vents up or down. As a result, the rear of the glass now sags a bit as it drops down slightly in order to retract into the roof, but now it can't pop upwards into a flush position. I’ve probed the pins on the back of the switch connector with a multimeter and it seems like both switches (for open/close and tilt/vent) still work correctly. Any ideas on what it could be, or where I should even start in terms of diagnosing? I'm sure someone's had this issue before but I haven't been able to find anything online relating to this specific issue, most of the issues are with the seals leaking or the motor failing entirely. Thanks in advance!
×
×
  • Create New...