Jump to content
SAU Community

Recommended Posts

  • Replies 14.2k
  • Created
  • Last Reply

Top Posters In This Topic

http://www.adelaidenow.com.au/motorcylist-...u-1225879513502

Very, very close to where I had my accident, and the cyclist was travelling in the same direction I was. Makes my stomach churn just thinking about it. RIP to the biker :)

+1

That section of road is rubbish. Had a mate go down probably that same corner too. We had to use a car to remove his bike from being wedged into the guard rail. He was busted up pretty bad, but nothing life threatening.

Does anyone know how to fit a lift kit to a hilux?

I'm sure I could do it myself, but I've never done it before and rather someone who's done it before help out :)

please help so I can fit some 35" tread!!!

suspension lift kye? if so it'll be easy as

spring and shock are normally separate, so its just a case of out with the old in with the new

Anywhere in Adelaide that will service/diagnose some Cusco coilovers that are knocking?

So far I've tried Manta but they didn't want to touch them.

Pillow ball mounts are stuffed....get rid of them.

Rubber mounts are fine for the street and occasional track work (and much quieter)....unless it's a track car, why bother with those things.

best way to remove battery corrosion?

soapy water and a rag?

baking soda and warm water in a small cup , into a paste then spread on corrosion, rinse with fresh water, but DO NOT get into open cells where you fill water

think you meant distilled water weezy ? it goes inside the battery

random car porn

gt1.jpg

i gotta do my whole boot :D

mix it in a sprayer a lot thinner it should bubble a lot then rinse with cool fresh water then dry,,,, any thick corrosion use a toothbrush or soft scrubber..

have fun...lol

PS it eats clothes slowly so do it with old crappy ones

only cost a few bucks to do it, look in the baking isle for baking soda

mix it in a sprayer a lot thinner it should bubble a lot then rinse with cool fresh water then dry,,,, any thick corrosion use a toothbrush or soft scrubber..

have fun...lol

PS it eats clothes slowly so do it with old crappy ones

only cost a few bucks to do it, look in the baking isle for baking soda

ive got a box of baking soda in the kitchen

just trying to work out what mixture to use as the last time i did it , well failed epicly because corrosion is back again ...

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Oh, also, forgot to add these photos I believe.
    • Thought i'd update on this. I was able to get in contact with Craig Lieberman and later on Darryl Alison (owner of Kaizo Industries). Darryl was able to help me verify that my car was in fact one of theirs and is helping me find more info on mine !
    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
×
×
  • Create New...