Jump to content
SAU Community

Recommended Posts

]']i was in my SKY white R32 GTR  

with plates JDM-32R

i was in the traffic in the opposite lane and u were in the non conjesting direction :)

Sometime before last weekend, were you going through the roadworks towards Castle Hill at the start of Castle Hill Road (Thompsons Corner) at about 2:00AM?

you know, WRX.

crappy, fwd, understeering thing

Im not sure, I might have got the brand wrong, was it a daewoo? kia?

hehehe!!!

yes i also spotted A-HUGE-xxx on the Anzac bridge, top down, wind in the hair - i think i may have even spotted you running your hand through your hair and glancing in the rear view mirror admiring yourself duncan! is that true?!? :wassup:

that wrx was the WRP10. priced halfway between a wrx and an sti, it has sti springs, sti ecu, sti wheels, sti front strut brace and lots of badges! it went really well. most impressed and more importantly heaps depressed that it reminded me of what a performance car was like to drive! :blast:

round 2:30 was driving near a maroon r33 plate was BENTY on penno rd

then about 3pm behind a r32 GTR gunmetal and no wing on kingsgrove rd

and while on kingrove rd i think i spotted Tommy K filling up at the shell servo

or another black R33 GTR

round 2:30 was driving near a maroon r33 plate was BENTY on penno rd

then about 3pm behind a r32 GTR gunmetal and no wing on kingsgrove rd

and while on kingrove rd i think i spotted Tommy K filling up at the shell servo

or another black R33 GTR

Benty works here @ ibm, he's parked near me before.

megeer silver 33 on pennant hills rd... boundary rd... new line rd... towards dural last night 9ish

white 33 with a huge rear wing turning right on to new line from castle hill rd this arvo at about 6:30

silver 33 on shepherds drive 6:30ish this arvo... even got a thumbs up :)

I spotted a white R33 series 2 parked on Coonara Avenue as I left the IBM carpark. It was parked, had the drivers window down (white number plates, can't remember plate).

That was me parked outside my mates place. :)

Saw a black GTR pull out of IBM as I left. GTR-**X

Sometime before last weekend, were you going through the roadworks towards Castle Hill at the start of Castle Hill Road (Thompsons Corner) at about 2:00AM?

um..yeap that would have been after my lil run with the curcuit club boyz through OP

where u driving oppostie direction from me?

should have waved :D

]']um..yeap that would have been after my lil run with the curcuit club boyz through OP

where u driving oppostie direction from me?

should have waved :D

I was about 2 cars behind you - this was before I got my R33 so I was driving the family Camry!

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • 1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • 3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...