Jump to content
SAU Community

Recommended Posts

Sure that wasnt NUR-66R?

I saw this one yesterday afternoon parked in its usual spot on the main road in Newtown

Beautiful car that one.

It may have been NUR-66R, it had blue slimline plates, in anycase a beautiful car.

Edited by Adam_54
JET#$R  coming back from old pac on sunday arvo

sorry dude I forgot your name!! My fault! :D:D:D

Your car looked and sounded very nice mate - awesome ride!

Cheers,

Chris

YiPPY..i spotted you too..glad to see a skyline flash me to greet me

Haha...nah just me coming out of a daze....(early morning)....

Thanks....

Your car looked nice...very very clean....

is that a 400r front bar?! hehe.. i don't usually like that bar, but it looks hot!!!!

thanks dude!!! hahaha... yeah.. nice and stock looking :P

Yeah, its the 400R bar....

I think its coz of the colour...

the colour attracts alot of attention though...(unwanted).

Someone tried to break into it last night....

My brother saw a Silvia S13 pull into my driveway last night at about 1am with its lights off....

My bro turned on his lights and they shit and got out of there.....

VERYY PAARRRANNOIIIDDD NOWWWWWWWW

yeah.. i was going to say the colour is half the appeal!!! :P i wouldn't have spotted you at all if i didn't see the splash of yellow amoungst all the traffic!!! hehehe... then it was excitement plus when i saw it was a sky!!!

ouch!! time to lock her away in a garage!!!! did your bro get the plates on the s13?

been seeing a few R31's near HITMAN(workshop) in penrith.

think i seen BWA thismorning wallgrove & GRT WSTN HWY lights,you was waiting for your lights to change,i was heading towards penrith.

about 5:30pm seen a chick driving a black 32gtst,at St Marys,turning right onto the highway into st marys,umm also a silver 33gtst MZQ-11k set of lights out front on Minchinbury,then a mum in a white 33gtst,then seen another 33 near the shell select at Eastern creek. all in a day.

oh and i been seing this white pulsar sedan 90 model(i think)

with fmic & looks like 4door 32 rear lights,looks good (Y)

Edited by RSTME
been seeing a few R31's near HITMAN(workshop) in penrith.

think i seen BWA thismorning wallgrove & GRT WSTN HWY lights,you was waiting for your lights to change,i was heading towards penrith.

about 5:30pm seen a chick driving a black 32gtst,at St Marys,turning right onto the highway into st marys,umm also a silver 33gtst MZQ-11k set of lights out front on Minchinbury,then a mum in a white 33gtst,then seen another 33 near the shell select at Eastern creek. all in a day.

oh and i been seing this white pulsar sedan 90 model(i think)

with fmic & looks like 4door 32 rear lights,looks good (Y)

yay I have only had the car a month and this is 5th time I was spotted :(:):D

I saw you on the great western actually but didn't know who it was what speed were you doing? lol

Oh and every day I see the same white R34 on wallgrove road in the morning

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...