Jump to content
SAU Community

Recommended Posts

First person to spot Liz's car with the new owner was....me!!!

20 mins after liz sold it he turned up at my place to pick up an airbox. I said hold on......This is Liz's car!...and ummmm, your not Liz?? What have you done with Liz? It was some dude nameed Nathan. Hope he takes care of that car liz.

I got new plates for two weeks now and nobody sports my car?? WAAAH

**runs into room and cries with a packets of tim tams and a DVD copy of Beaches**

lol! he called me yesterday (to talk about a suspension problem) and said you were so excited yet distraught that someone else was driving my car.

I hope he enjoys it as much as I did :(

:( damn.... where do ya work man???

Was coming back from doing a Nasho run where i spotted a burgundy 33... parked at Stamwell then a gunmetal 32 on the way back... they've fixed the road between the 35km/h and the 25km/hr turns.... smooooooov!

should be good for those who turn up this friday

Are you coming on Friday?

I spotted you just near the Crystal carwash, i work near there

Spotted wink on his way to work on Beecroft Rd! Left lane PWNAGE Wink :)

Then i got stuck cause i had to drop mona off on the left and get all the way back across to the far right in bumper to bumper traffic :laugh:

lol

Should've been smart like me then.

I dropped my brother off when I was stopped in traffic just before the bridge - no need to pull over to parking area... :laugh:

Also you almost ran a red light at the M2 exit lights. You made it by a millisecond. :O

i saw you both on becroft rd, i was a little way behind again like usal.. wink, i saw you wave, was that to me? i waved back

saw a nice black 32 with impuls and red brakes near queens park just then

thats me.. you sure red? they're blue :)

Spotted a Silver/grey r34 gtt towers bus bay around 3:30ish

Spotted a silver r32 gts-t with aftermarket skirts reversing into a house on showground rd

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • So, this shouldn't be such a mission, but there were a few tricks so I thought I'd post up a DIY for it. This was on a Q50 Red Sport but I doubt any other V37 model is very different (maybe just less steps for the intake heat exchanger hoses) I pulled the radiator out to flush it because the car was running hot at the track, but obviously the same steps apply for changing a radiator for any reason including an upgrade. If you are removing the radiator, you of course need to drain and refill, so have 5+ litres of blue coolant ready. You don't need to drain the intake heat exchanger to remove the radiator but depending on your plans you may need a couple of litres for that as well. You will also need something to deal with the auto transmission lines, I used 2x 8mm rubber caps on the radiator side, and a short length of 8mm pipe on the car side.....unless you can block these lines quickly you will loose AT fluid and it may be enough to hurt the transmission if you don't refill it. Other than that....lets go... "First, jack up your car". Yes really, and put it safely on stands. If you are not confident doing that you need to give this job to a mechanic
    • If the forester is anything like our old 2007 GTB Liberty, I could near on run ling Long's and "rate them", as no matter what, it just hung to the road, even when abusing it in a hard launch in the wet, or throwing it at corners.
    • LOL, all of the CAI like Craig I just need to put a hole saw through my bumper Done and dusted, the car runs, which is nice, I'll take it for a spin when the weather clears up Just need to put the bumper back on for good
    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
×
×
  • Create New...