Jump to content
SAU Community

Recommended Posts

at carlingford road tonight at 7:20 there was 3 R33's in a row waiting at the traffic lights approaching Pennant Hills road, me, a white r33 series one in the middle, and another silver on the other side, pretty cool sight.... too bad the white r33 guy drove like a douche accelerating all the time while he should really just be cruising.... he looked angry and all that, looks like somebody had just as shitty day as me, atleast his car was in good nick

I work just around the corner from there in the Alfa workshop!!

there is also a very nice silver kitted R34 gtt that parks there!

Yeah that 34 is very nice. Used to see it there all the time.

I work up at mazda now around the corner. Small world!

Yeah that 34 is very nice. Used to see it there all the time.

I work up at mazda now around the corner. Small world!

Ahh euro cars!! U know chris in the workshop...lives up at gosford way!!

Spotted a silver 34 in the army barracks at moorebank tonight, have seen it their quite a bit actually.

mm what you doing there lol..

Spotted a gold R32 GTR in penrith tonight, plates were "AXN.03Q"

and

a Gun grey R32 Gtst on sunnyholt rd, plates were" AJ.96.LI"

mm what you doing there lol..

Spotted a gold R32 GTR in penrith tonight, plates were "AXN.03Q"

and

a Gun grey R32 Gtst on sunnyholt rd, plates were" AJ.96.LI"

lol my mates in the army he lives on base their im usually their once a week or so

spotted mr GOLDZILLA in his stagea at pennant hills heading north bound past boundary road at about 7:20ish tonight

Oh, I didn't see you Tom, were you in stealth mode in some other car?

Oh, I didn't see you Tom, were you in stealth mode in some other car?

nope i was in the line with the lights on, i don't know how you missed the back of the car (looks like an electric stove top), you drove right next to me lol..... i guess their was traffic and you were approaching the traffic lights and their were trucks around aswell, i guess you were doing what we all should be doing and actually paying attention to the roads lol

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Did and sync timing with light 
    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
×
×
  • Create New...