Jump to content
SAU Community

Recommended Posts

Did dyno run a few weeks ago and now wondering what it means and how much more can be gained. Setup is fairly stock, 3" turbo back, 12psi, superspark coils.

My limited knowledge of AFR's tells me this gets fairly rich, and by getting the WOT AFR closer to 12.5-13.2 I could squeeze more power from it? Can anyone estimate how much? And what would be the best method, haltech, safc, pfc (nothing wrong with future proofing :(

Only have the boost/afr part pic of the sheet with me at work, if the whole sheet is required then I'll upload once home. Also, what causes the 10. flat spot at the end of the run, injectors maxed/ecu?

post-63773-1257477377_thumb.jpg

Thanks!

Link to comment
https://www.sau.com.au/forums/topic/295126-yet-another-dyno-sheet-thread/
Share on other sites

I wouldn't really go leaner than 12:1 personally, the high 12/low 13 AFRs are ratios suited to NA cars... turbo cars like a fatter mixture but yes, the air fuel ratios you have are terrible. I'd consider checking to make sure you don't have an air leak somewhere.

here in nz we get 220-240kw on 12psi out of stock rb25det with front mount and 3" exhuast and a link ecu on dynapack hub dynos

standard injectors are maxed about 230kw although we have got 237kw on stock injectors.

safe and ideal af ratio for turbo car is between 11.6 and 12. 11.8 is the aim

getting an ecu that runs with out an afm is always good. depends on what your tuners in your area are familar with.

220-240rwkw out of a stock turbo is stupidly innacurate. your dyno is just plain wrong if its spitting out figures like that with a stock turbo, especially with a stock ecu

as said 12:1 is ideal under full load for a turbo car

220-240rwkw out of a stock turbo is stupidly innacurate. your dyno is just plain wrong if its spitting out figures like that with a stock turbo, especially with a stock ecu

as said 12:1 is ideal under full load for a turbo car

+1

From all what I have read, 200rwkw is about the max you can make with just 'basic mods' for the RB25DET. Moving beyond 200rwkw most likely need a aftermarket turbo or high flowed stock one & run more boost & also require the supporting mods.

For reference, my auto 33 made ~180rwkw with basic mods (3" turbo back exhuast, R34GTT SMIC, bleed valve +10psi setting & SAFC II)

220-240rwkw out of a stock turbo is stupidly innacurate. your dyno is just plain wrong if its spitting out figures like that with a stock turbo, especially with a stock ecu

as said 12:1 is ideal under full load for a turbo car

A hub dyno will always read higher KW figures over a roller dyno.

Their figures are quite accurate for the dynos they're being measured on. You can't compare, and this is why dynos are BULLSHIT.

if you read my post i had said Link ecu(i think its called vipec over there)

dynapack hub dynos are the most repeatable dynos out there, hence why nascars etc are tuned on them, as there is no crap like tyre slip etc

only thing they lack is a shootout mode for comparing against other dynos.

ie if you do 2 runs in a row. with out changing anything the runs will be within .2% of each other.

most people don't push stock turbos above 220kw.

here is the 2 that im talking about on this page. the first one is r34 neo rb25det(VVT isnt working), the 2nd is r33 rb25det. both with links, front mount and exhuast

http://www.skylinesdownunder.com/forums/sh...8244&page=2

my r33 with stock turbo, front mount, 3" exhuast made 220kw on 10psi on a basic road tune with a LINK ecu.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For these last 7 years of ownership, I've always had to use a small scissor jack under one of the front tow hooks to raise the front just enough so my low-profile jack fits under to reach my subframe jack point. I'm beginning to get annoyed of always having to do this. Are there any lower low-profile jacks that fit under the gtr lip on a dropped car?
    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
×
×
  • Create New...