Jump to content
SAU Community

Recommended Posts

Hi all,

No doubt some of you know Im having problems with an RB25 overfueling at idle. Injector pulse at idle is 7ms! Car runs in limp mode, idles smoothly & does not smoke (although it smells a bit rich) until AFM wires are pulled or played with, then it starts pouring black smoke, hunting real bad & AFM signal voltage sits on around 2.4v at idle... Obviously I strongly suspect AFM circuit but AFM & ECU have been swapped & AFM wiring has been checked for resistance to ECU, resistance to earth, shorts, etc & I cant fault it! Have also tried removing AFM plug & hooking wires straight to AFM...

Anyway if things dont get sorted soon Im wondering if I could go for a remap & get fuel maps changed to provide the correct amount of fuel?

I know its a band-aid solution & probably not ideal & I would much rather find & fix the problem but this is getting ridiculous & Im getting desperate. Have no idea whats going on & neither does anyone else it seems...

Just wondering what peoples opinions are on this?

Thanks

Link to comment
https://www.sau.com.au/forums/topic/296180-remap-to-mask-overfueling-problem/
Share on other sites

sucks that you are having so much trouble with this man.

the only thing that i can think of is a knock sensor kicking in, it won't show up as a fault on the ECU. you can test it if put a 1M ohm resistor between the signal wire and ground thats tricks it into think everything is fine.

what is injector pulse and AFM voltage supposed to be?

i got no idea if a tune will fix it, trent from status would be the man to talk to though.

seriously just take it somewhere, any workshop worth a damn should be able to sort it.

Remapping aint gonna do shit, i know i wont touch a car for a tune unless it is bug free... i doubt anyone else would either.

Edited by URAS
sucks that you are having so much trouble with this man.

the only thing that i can think of is a knock sensor kicking in, it won't show up as a fault on the ECU. you can test it if put a 1M ohm resistor between the signal wire and ground thats tricks it into think everything is fine.

what is injector pulse and AFM voltage supposed to be?

i got no idea if a tune will fix it, trent from status would be the man to talk to though.

Yeah... I know...

OK, will try that. Willing to give anything a shot...

Injector pulse width at idle should be 2-2.8ms & AFM signal should be around 1.5v

seriously just take it somewhere, any workshop worth a damn should be able to sort it.

Remapping aint gonna do shit, i know i wont touch a car for a tune unless it is bug free... i doubt anyone else would either.

OK, thanks for the honest opinion. Wanted to hear from someone like yourself who actually tunes cars...

Figured it was worth a shot asking. Actually a mechanic myself so as you can imagine, hate taking my car to the shop. Problem is I rebuild automatic transmissions so dont have much in way of engine diagnosis tools at work... Also dont trust many general mechanics knowledge of imports...

What is your going rate for this sort of thing? I am just in Cranbourne & work in Sth Dande too... (A & B Automotive Remanufacturing)

If you dont want to discuss prices on here drop me a PM or I will call Monday. Will probly also be after a remap once this is all sorted too

Opinion? Take it to a professional.

It'd be lucky to cost more than $250

Yeah, I hope your right...

ROFL I was about to suggest you just take it Trent. Really is worth the wait. It has been my (and a number of my friends) experience that someone with the level of experience of Trent is going to diagnose your problems in a fraction of the time with a lot less mucking around. From there it is usually a relatively simple process to rectify. In the Victoria section is a list of other workshops that might have time to take a look (although it seems everyone is flat out before xmas!).

any competent workshop that knows auto elec and skylines can fix it

why on earth would you wait 1.5 months? there must be a dozen recommended sau vic workshops, check the thread at the top of the vic section

thanks for the support guys i appreciate it alot but like i posted earlier there are plenty of guys who should be able to sort it quick smart, i seriuosly would not wait 1.5 months so why should you.

My business revolves around tuning and engine building everything else takes second tier to that, i can usually squeeze in tuning and so forth but i cant push around tuning jobs for diag as its not my core business.

These are workshops i could reccomend to get the job done fuss free;

RACEPACE

CREATD

RE CUSTOMS

HI TORQUE

CHASERS

Edited by URAS
I would love to help you out but im booked into the new year, sorry. Try Re customs or hi-torque.

Any chance for a full power fc tune for a r33 some time in december trent? Ill give you a call during the week.

Edited by skline01999

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For these last 7 years of ownership, I've always had to use a small scissor jack under one of the front tow hooks to raise the front just enough so my low-profile jack fits under to reach my subframe jack point. I'm beginning to get annoyed of always having to do this. Are there any lower low-profile jacks that fit under the gtr lip on a dropped car?
    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
×
×
  • Create New...