Jump to content
SAU Community

Recommended Posts

No point buying a FMIC if you wanna beat him down the 1/4, go and get some fat 245 or 255's on the rear along with a set of pineapples.

Also put your spare tyre back in and try it again, removing weight from the rear end of the car will give you less traction which is why you may have spun your wheels alot.

On my first attempt I only managed a 14.46sec, my excuse is severe axle tramp which I put down to removing weight from the rear of my car (spare tyre, sub box and other misc things) and also being on a prep'd track with a totally different surface to your regular road.

Keep trying, dragging in a manual is an art that takes a while to master, and this shold be evident in the differences in your 60' times.

To be honest though, with exhaust, diff change and ls1edit, his times are about 1/2 second (or more) slower than they should be too.

I reckon a FMIC will help you. When I put mine on my car I remember feeling a huge difference, especially in the midrange.

Also I agree with chops ... the VX should have been quicker with exhaust and ls1 edit. Diff gears depends what he's got ... 3.9:1 might not help him so much over the quarter, but good for initial accel.

Thanks for all the advice guys i cant wait to go back and try some of the tips out on the track...

I was actually running with my spare in the boot, and my wheels are 235, so ithink i am just a bit of a spaz.

This may sound like a stupid question but what are these pinapples that people keep going on about

  • 3 weeks later...

you *should*, should, with some more practice get it down to a flat 14sec. A 60' of about 2.1 and ET of 102mph or so should see it in. You're close on the ET, i'd say you're losing 0.4 sec in the takeoff. Best not to drag direct against a person anyhow, cause generally the "heat" of trying makes you fug something up.

damn, i wish i could get my car back out there on strip. Its gonna be a couple of months ..*withdrawal*

I'd say the MOST important thing for a boosted R33 is to sort your A/F ratio's out! Invest in a SAFC, or PowerFC if u can afford it. The SAFC by far made the biggest difference for my car. With the mods you have, you should see some huge gains - 20 - 30rwkw.

Do a search on SAFC, and see what other peoples feedback has been once their A/F ratios were sorted.

  • 1 month later...

ahaha i love this,

your a feathers length off beating the top of the range most powerful and expensive holden... and your in a gtst :D:)

not many holden 'heads' are aware that there is a gtst skyline.. AND then there is a GTR skyline

:devfu: ;) :kick:

Sort out your shift points. I find holding the gear just that little bit longer where it sounds like it is starting to over rev a little to be the best shift point.

Generally in the 32 that is around 7100rpm depending on what boost I am running.

His has the Exhaust done, diff ratios changed, and his computer reprogrammed.

I would consider your car to have very minimal mods compared to his, Pods arn't a 'power' mod they don't make any more power. Well on mine it didn't - Back to back on the dyno.

If I were him I would be dissapointed with a 14flat as hell what would he have got with only an exhaust. Taking in to account that you ran your quickest time on std boost.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...