Jump to content
SAU Community

Recommended Posts

A bog stock falcon doesn't lose half its power in summer compared to winter thought, my point was, whilst a turbo car technically will lose more, it shouldn't lose half it's power, hence the standard air boxes are the way to go.

i have the air temp sensor between the intercooler and throttle body so it measures the air going into the throttle body.

the other day when i started the car it was at 0deg and after warming the car up it went up to 2 deg. it is cold here

as for your cars in the heat, just dont thrash it for extended periods of time. give it a squirt every now and then but then also give it some time to cool down a bit and it should be fine.

A bog stock falcon doesn't lose half its power in summer compared to winter thought, my point was, whilst a turbo car technically will lose more, it shouldn't lose half it's power, hence the standard air boxes are the way to go.

my pod sits on the front of my turbo and i cant say i have noticed a huge difference, 3rd has slightly less traction when its cold but thats about it.

my pod sits on the front of my turbo and i cant say i have noticed a huge difference, 3rd has slightly less traction when its cold but thats about it.

Well if you are having trouble with traction in 3rd when its hot I think we can safetly assume you have enough power that it simply doesn't matter :blink:

I was mainly refering to dudes with stock rb20/25s.

Hahaha

Has any one else got any air intake temperature readings/graphs to compare to mine? Possibly with a decent airbox setup?

Honestly compared to a hot day and a nice cool night mine feels like two different cars. Similar to the difference with driving by yourself or three other people in the car.

my setup is an apexi pod in a cold air box with cai from the grille...

cooler is a hybrid gt

on a hot day i really barely notice any difference

I might look into getting an oil cooler, ive heard people covering or blocking them up during the colder parts of the year due to oil temps taking too long to warm up, or something along those lines.

if anyone could give insight as to how much id be looking at to get one fitted to a stock r33 gtst? cheers. also do they all have to be mounted behind the drivers side fog lights? or is there another place better suited?

thanks!

Stick to the standard air box with a high flow panel filter. I´m running 250rwkw and barely notice any major reduction in performance on hotter days. Adding three passengers in the car results in a different story...

Keep in mind as well that it´s not just the hotter weather but the humidity that affects the performance of our turbo beasts. Car companies calculate power using the specific heat of DRY air. I know for a fact that a NA car on a 85% humidity day can theoretically have almost 10% less power than on a 25% humidity day... This would be higher on a turbocharged vehicle. Anyway, a little extra info for all the car nuts out there :)

btw, I´m not pulling this out of my A$$, I just finished my final year project on this kind of study.

Mine is only a bit slower on hot days - no issues with over temp. Running china-spec larger radiator, HDi FMIC, standard airbox with K&N filter. Running 10psi on stock turbo - seems dandy. I'm even getting frosted air out of the AC on humid days.

Actually I would say a large radiator is better protection.

from my previous experience, by just installing an oil cooler, water temps stay more constant. As oil temps go up, water temps follow because of the heat exchanger near the oil filter which uses water to cool down the water or uses the water to bring up the oil temp when the car is cold.

Yes a better radiator will cool more, but installing an oil cooler will

1. keep oil temps optimal 2. keep the overall engine temps down.

If you install both an aftermarket oil and water temp gauge you'll know what I mean.

I don't think I articulated this that well.. friday at work, blah :blink:

i know i should check with a gauge, but if the water temp stays fairly low then is it safe to assume the oil temps stay fairly low to? my oil pressure seams to stay higher which would suggest the oils not getting hot enough

Stick to the standard air box with a high flow panel filter. I´m running 250rwkw and barely notice any major reduction in performance on hotter days. Adding three passengers in the car results in a different story...

Keep in mind as well that it´s not just the hotter weather but the humidity that affects the performance of our turbo beasts. Car companies calculate power using the specific heat of DRY air. I know for a fact that a NA car on a 85% humidity day can theoretically have almost 10% less power than on a 25% humidity day... This would be higher on a turbocharged vehicle. Anyway, a little extra info for all the car nuts out there :blink:

btw, I´m not pulling this out of my A$$, I just finished my final year project on this kind of study.

Hmm there you go, must be the huge humidity that we get up here that kills the performance.

Edited by PM-R33
How high is 'higher' ?

its really hot here today (37+) and water temp creeped up to 78C (highest it ever gets) and the oil pressure got done to about 1.5kg/cm2 at 850 idle. usually stays up around 3-4kg until it gets over 70C. thats with hpr5 (5w-40). thinking about going even thinner oil after summer, it takes way too long to get hot enough to get down to the right pressure

Edited by JonnoHR31

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
×
×
  • Create New...