Jump to content
SAU Community

R34 Gtt Overheated Due To No Water/coolant, Now Engine Light

Alien

By Alien,
in Engines & Forced Induction

 Share

Recommended Posts

Alien Grand Master

Alien

Posted
Posted

Hey guys

Long time since I've been here as I havent been driving my 34 for months now. Due to this, after taking it for a drive yesterday, after driving for about 20 mins, the car started going a bit sluggish and lost all power and had engine light on. I pulled over and as I thought, overheat. There was no water/coolant left at all and wat was left was extremenly hot and boiling. I let the car cool off a bit while I waited to get some water bottles delivered to me and then filled up around 5 litres of water into radiator and the water/coolant tank. The car started up fine, runs fine and everything but the orange engine light stays on in the dash. Its not coilpacks as I've installed Splitfires already and the car still runs fine.

How can I get rid of this engine light now? Is it meant to stay on until somebody manually clears it with a diagnostic tool? Or is there something or some parts that stuffed up due to overheat? Also, should I go get a full radiator flush and who is a good mechanic these days for skylines around Sydney west?

Thanks guys

DarkZ

vidospace Mentor

vidospace

Posted
Posted

Yes you should flush the radiator.

You shouldnt have filled it with water only, it needs coolant specifically.

The bigger issue than the light on the dash is why it ran out of coolant at all? Was it blowing smoke? You might have a blown cylinder head too!

Re the light though. Yes you can reset it with a consult cable.

noone Experienced

noone

Posted
Posted

As above I would be just as worried about where the water went

and probable head gasket damage

On most cars disconnecting the battery overnight or disconnect than stand on the brakes for 30 seconds

tends to clear engine lights, resets the computer

however will come back on when it starts if the fault is still there?????

Have not tried this on a skyline but works on nearly everything else I have tried it on

West Grand Master

West

Posted
Posted

RB's are tough nut when it comes to the over-heat thing, i once left my radiator cap out, drove the car for 20km or more until i see steam coming out of the bonnet. Shat myself but the bloody thing still going even after 3 years later.

666DAN Grand Master

666DAN

Posted
Posted (edited)

Yep best to run the diagnostic and see what it says....could be anything from a damaged sensor to coolant water shorting something out. Until it's rectified the light won't go.

Saying that though, I do recall a something about the ECU needing to be reset after logging an overheat code, but yeah follow the thing below and it shows how to reset with a paper clip

Diagnostic

Edited by 666DAN
Alien Grand Master

Alien

Posted
  • Author
Posted

thanks for the info guys

I havent driven the car for a long time and maybe from recent heat the coolant just evapourated, if thats even possible. I will flush it out asap, just need to find a good mechanic specialising in lines.

Cheers

  • 3 weeks later...
Alien Grand Master

Alien

Posted
  • Author
Posted

hey guys

I havent had a chance to take the car to a mechanic so I had a look just before and its still spitting out water from underneath the car. So I had a look at engine bay and found a fairly high pressured leak - I'm assuming a crack at one of the pipes. Its all the way at the back of the engine so I can't really spot it.

Is this just a matter of replacing the plastic pipes or is it something more serious?

Cheers and happy new year!

DECIM8 Grand Master

DECIM8

Posted
Posted (edited)

I know what it is.. Its the part sitting behind the firewall. Exact same issue I had with my car. I made a thread about it ages ago.

The part corrodes over time as its metal, I figure its the same thing.

P.S the car doesnt need coolant thats just to stop it rusting. Good to see you back thought you might have written off the car/sold it as I spotted it for sale on st george website. weird.

Position of the leak is drivers side about 10-20 in from the side of the engine and about 30cm down and in the worst spot you can imagine.

Edited by DECIM8
Jezza-gtR Mentor

Jezza-gtR

Posted
Posted
P.S the car doesnt need coolant thats just to stop it rusting. Good to see you back thought you might have written off the car/sold it as I spotted it for sale on st george website. weird.

A car does need coolant, the main function of coolant is to raise the boiling point of water. You won't get far with 100% water in your system.

Alien Grand Master

Alien

Posted
  • Author
Posted
I know what it is.. Its the part sitting behind the firewall. Exact same issue I had with my car. I made a thread about it ages ago.

The part corrodes over time as its metal, I figure its the same thing.

P.S the car doesnt need coolant thats just to stop it rusting. Good to see you back thought you might have written off the car/sold it as I spotted it for sale on st george website. weird.

Position of the leak is drivers side about 10-20 in from the side of the engine and about 30cm down and in the worst spot you can imagine.

Hey dude long time no speak

Are you sure it was my exact 34 that was on sale as I never had it up for sale on any classifieds site. Which St George site?

As for the leak, how do I go about reaching for it and whats the replacement part I need and where could I grab it from? Do you have a link to the thread?

Thanks man

l_uk3y Proficient

l_uk3y

Posted
Posted

Now someone feel free to correct me if they want. But to my knowledge the coolant actually increases the waters boiling temperature above 100 degrees. (besides other tasks). Either way I've never heard anything good about running water only.

That said I ran water only and lost my radiator cap on my old pintara about 6 or so years ago. Had no issues driving around like that (with no cap) for a week before I got a new cap (I don't condone this at all though). I babied the car the whole time though

JonnoHR31 Grand Master

JonnoHR31

Posted
Posted

water transfers heat a little better than coolant but its not a good idea in a RB, alloy head doesnt like corrosive water. the pressure of the system raises the boiling point higher than 100 with straight water and coolant is higher again

Alien Grand Master

Alien

Posted
  • Author
Posted

I found the leak... it is in the worst part of the engine bay, right behing the engine. Its the metal bit where you clamp on a thin hose to a bigger hose. No idea how I can fix this or anybody else as it is practicaly unreachable with tools etc. I was able to get my hand in there and touch the crack to stop the leak but how can I actually repair it? Can I just change the whole hose somehow?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Waders360
      M35 Brake caliper replacement

      By Waders360 · Posted

      Sorry. Front brake calipers
    • MBS206
      S1 rb25/s14 starting problem

      By MBS206 · Posted

      Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
×
×
  • Create New...