Jump to content
SAU Community

Recommended Posts

Hi all,

Just thought I'd post some info here about the process I'm currently going through with my series 2 RS-Four (V). It all started with a rather nasty tappet rattle (which I thought was just the change to Castrol 5w/30 oil) in September. But it turned out to be something rather worse than that and it has been at the mechanics getting a full engine rebuild for about the last month.

Cause turned out to be sand blasting grit getting into the oil. This wore the head quite badly and deposits of the alloy paste from the head and some sandblasting grit can be seen in this photo of the sump:

post-32445-1260611950_thumb.jpg

post-32445-1260612496_thumb.jpg

How did the grit get in there? Well, probably when I got my rocker covers powdercoated about 6 months ago. I took all the usual precautions, including taping every orifice (and tape was still on there even after the powdercoating process) and blasting out the baffles with 100psi compressed air and solvent afterwards. I didn't notice any grit coming out. But it must have later on. A stupid thing to do maybe but oh well, we don't repair - we improve...

So I managed to get hold of another NEO R34 head off a forum member on SAU for $300 and got it rebuilt at a machinists; the block has been hot-tanked, bored, the crank washed and micro-polished etc. and the bottom end has been rebuilt with CP pistons at first oversize. Things are progressing and I have got some photos of the rebuild which I will post some of after I've checked them out over the next week.

So getting it back together... slowly. Will eventually have something with 0 kms on it though, which sounds bloody good. Especially since even at 130,000k's it still sounded/felt new. Oh, and fingers crossed but for those of you who may be considering it, it does look like you can get a decent rebuild with forged pistons for under 10 grand... but wait until I've got the first few thousand k's on it yet before I can say for sure >_<

Link to comment
https://www.sau.com.au/forums/topic/299941-rb25-engine-rebuild/
Share on other sites

yeah you can get a whole kit from ebay (ericsperformanceparts on usa - Ive bought a few grand of gear from him for the head and he is a great bloke to deal with)

the kit for under $1500 aus delivered includes:

CP pistons 86 or 87mm

Eagle Hbeam conrods

arp rod bolts

http://cgi.ebay.com/ebaymotors/ws/eBayISAP...RK%3AMEWAX%3AIT

there was another one, same price, that included acl race bearings as well but forget where I found it on ebay - deal might be off I suppose.

so add in $350 for acl race bearing kit, another $1000 for gates timing belt/pulley kit + N1 oil and water pumps, full Cometic gasket kit for everything to be replaced for around $450, and $200 for fuel filter/oil filter(s) and oil(s)

thats around $3500 for parts, and then the labour.

could be rebuilt for around the $6000 mark IMHO

.... well that will be my aim when Im ready to go down that path, and that with the $4000 ported head/tomei cams = $10k for the whole engine build from top to bottom

:D

yeah you can get a whole kit from ebay (ericsperformanceparts on usa - Ive bought a few grand of gear from him for the head and he is a great bloke to deal with)

the kit for under $1500 aus delivered includes:

CP pistons 86 or 87mm

Eagle Hbeam conrods

arp rod bolts

http://cgi.ebay.com/ebaymotors/ws/eBayISAP...RK%3AMEWAX%3AIT

there was another one, same price, that included acl race bearings as well but forget where I found it on ebay - deal might be off I suppose.

so add in $350 for acl race bearing kit, another $1000 for gates timing belt/pulley kit + N1 oil and water pumps, full Cometic gasket kit for everything to be replaced for around $450, and $200 for fuel filter/oil filter(s) and oil(s)

thats around $3500 for parts, and then the labour.

could be rebuilt for around the $6000 mark IMHO

.... well that will be my aim when Im ready to go down that path, and that with the $4000 ported head/tomei cams = $10k for the whole engine build from top to bottom

:D

your budget seems about right. Do you have an overlay of before/after with the cams?

Blew my engine (well it still runs but with a few broken rings huge blowby etc) and considered the options. Thought about a stock recondition like Dave - great for peace of mind knowing everything is new - and should be able to handle up to 270awkw comfortably.

However looking for more power next year. Full recond with forged components, balanced etc heading towards $10k. Second hand RB26 too much of a gamble and still need money spent to get more than the 245kw i had with the present RB25 so now going with an RB30. Should be good for around 270kw (stage 1 with the GCG turbo) and will stand around 300 to 350 with a bigger turbo etc later next year. Well that's the theory...will let you know how it pans out.

Blew my engine (well it still runs but with a few broken rings huge blowby etc) and considered the options. Thought about a stock recondition like Dave - great for peace of mind knowing everything is new - and should be able to handle up to 270awkw comfortably.

However looking for more power next year. Full recond with forged components, balanced etc heading towards $10k. Second hand RB26 too much of a gamble and still need money spent to get more than the 245kw i had with the present RB25 so now going with an RB30. Should be good for around 270kw (stage 1 with the GCG turbo) and will stand around 300 to 350 with a bigger turbo etc later next year. Well that's the theory...will let you know how it pans out.

Going a RIPS bottom end with your head and one of their sump adapters?

Going a RIPS bottom end with your head and one of their sump adapters?
RIPS do quality work - their price $5000. However have confidence that local engineers can do the job for 10 - 20% less. I need to save some money for the Link (Vipec).

Nice pintaline and Rob... wish I had the time & access to more RB30DET resources. But my rebuilt RB25DET is finished and ready; another set of rocker covers are getting colour matched to the "precious steel pearl" powder coat of my original ones (but in plain old enamel this time :)) and tomorrow it's back into the car hooray... mechanic is very confident that it's all going to be happy and will not bind/have large clearances etc etc. Makes me feel better too...

Have some photos which I will get back tomorrow or the next day of the build and (hopefully) install. A stagea with an empty engine bay is a sorry sight :( Engine is all rebuilt now though and it looks great. Block's been hot-tanked and painted with new welsh plugs... really looks the part. Now just need to get the rocker covers coated again and should be back looking like new. The guys who are assembling it have really made light work of such a big job (for me, without a hoist)... it's not gonna be real light on the wallet but oh well, I'll only be doing this once I guess, may as well enjoy it while I have the chance to have a 0km engine :cool:

Edited by DaveB

Nice. How much for RB30 sump adapter kits? I know the full-on baffled sumps are damned expensive...

Well I have finally got the stagea back on the road!!! Rebuilt engine is running v nicely... can't really tell much difference from how it was before, except that the loud as rattle is gone, and sounds very nice and smooth. Idle is better, doesn't rev out to 1,500-2,000 rpm at startup. Sounds nice and 'burbly', a little more like an RB IMO. Total bill for the rebuild, including labour, was about $5k + bits (for me I would add $800 for the pistons so that's ~$5,800 so say 6 grand). Not cheap but *everything's new* :( (or rebuilt anyway). All nice and shiny now :cheers: Got to get hold of the photos of the assembly...

Edited by DaveB

Cheers Hartley, surrrre am! The break-in sucks already though and I've only done about 150K's (of 1,000) :D

The difficulty I'm having is that the instructions were basically "drive it off-boost, between 2k-4k rpm, up hills is good (give it a 'light workout' - accelerate moderately up to ~4k rpm) but NO BOOST!" (well 1-2psi is ok lol)

...this is hard because

a) the stagea drinks fuel when driven between 2-4k everywhere (I've locked out overdrive - gearbox in '3') and

b) with the hi-flow and exhaust, driving at those rev's, it's pretty hard to keep the stagea OFF boost :)

so break-in is fun but I can say... even off boost, the stagea is faster than a few cars I have driven :) So glad to have power steering and climate control back too.

If you run it in too gently you will just glaze the bores and it will always use oil. Can you lock it in any gear? i.e. get rid of the freewheeling? Turn the overdrive off?

Then accelerate briskly (keeping the boost to a minimum) to 5 -6k revs and then lift off letting it go down to 2-3K and repeat. Watch the temp guage. Listen for any strange sounds, watch the temps and now and again look under the bonnet for any leaks etc.

if there are no problems kep increasing the revs to 5, 5500, 6000, 6500 without flooring the pedal. I would do my running in in one day and then get the car back asap to get the head retorqued and change the oil and filter.

Thanks for the advice. Yeah I was recommended "light hills work" and to keep rev's between about 2 and 4/4.5. I have to do 1,000K's apparently before I take it back to get the first oil change and inspection. Also the head bolts are apparently not going to be re-torqued, as this is a feature of the 3-layer metal head gasket. I'll go do some 'light hills work' sometime soon lol.

hearing a bit of a funny noise around the passenger footwell area at about 3,000 revs or so; like the climate control fan makes when it has leaves in there; doesn't sound engine-related but I'll mention it to the workshop on my visit in the new year.

from another site

http://www.flyinmiata.com/tech/breakin.php

Keep in mind that there really shouldn’t be any metal to metal contact happening within your engine, other than the rings to the cylinder walls. The rings are the ONLY things we are interested in breaking in or seating. What seats rings is cylinder pressure. Rings and pistons are designed so that cylinder pressure sneaks behind the compression rings and forces them out against the newly honed cylinder wall. Why do I mention this? Because I want you to take your warmed up car out on the road, find a nice straight stretch and do a couple of heavy throttle runs in third or fourth gear from about 2500-5500 rpm. Each time you hit 5500-6000 rpm, snap your foot off the gas and let the car coast down to 2500 rpm while in gear, to pull high vacuum in the cylinders. Repeat this step about five times and you should have a nicely mated set of rings and cylinders. NOTE: When I say “heavy throttle”, I am referring to a normally aspirated engine. For a turbo or supercharged car, modulate the throttle to achieve about zero on your boost gauge, rather than full throttle. This would be roughly equivalent to full throttle in a normally aspirated car.

Yep Wolverine is spot on. I was taught by a very qualified engineer to do my running in mostly in the first couple of hours. The only top to bottom recondition that i did when I was a mechanic was on my own six cylinder Austin Healey 3000 and I ran that in (and subsequent engines that i bought) that way.

Basically you want to push a lot harder than just 2 - 4500 revs. Give it heaps as they say here avoiding only labouring in too high a gear or hammering the rev limiter.

Wolverine describes the process to a T in the above post.

Thanks guys, yes that sounds pretty good. I didn't realise break-in should be done so early.

But if it's in the first couple hours of "engine time" (eg. running time) then I managed that... it was on about the 3rd day but after only about 80-100k's of driving.

I took it to some hills roads and did a few runs, mostly in 2nd, from ~2,000 revs to 4, 4 1/2, 5 or thereabouts, trying hard to keep boost on zero. This is not easy! Especially when you have the split front dump, the hi-flow cat, the ball bearing turbo, the straight-through exhaust etc. etc. all tuned to make boost by 2,000 in 2nd... so when you say "hard", I am not sure if what I'm doing is "hard"... but it's as hard as I can make it without making more than 1-2psi max boost.

Pretty sure I have the idea though thanks; I have been increasing the rev's a bit; haven't tried in a lower gear though like 3rd or 4th as a) boost builds too easily b) doing warp speed by 4,000 revs and c) I subsequently run out of road :)

I wondered about coasting down after accelerating or just changing gears to let the rev's drop quickly (because I'm in an auto, coasting back to 2,000 revs again can take quite a while) but I read somewhere that suddenly dropping the rev's was bad, so I coasted :( Sounding and running great so far, haven't lost any coolant or oil so fingers crossed... will be the new year before I can get that first oil change though.

Edited by DaveB

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
×
×
  • Create New...