Jump to content
SAU Community

Recommended Posts

Be carefull letting out secrets of the 'experienced' Richard, we will soon have a lot of young male 'Line drivers getting around with erect nipples and not so 'johnsons' .... :yes:

I think a rap/poem is needed for erected nipples and not so johnsons.

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/910/#findComment-7149628
Share on other sites

I think a rap/poem is needed for erected nipples and not so johnsons.

Richard is da man

For experience and advice,

If he tells ya somethin'

He don't have to say it twice ...

He speaks from a well worn road

Of years of workin' it out,

And if you need to make it work

Put ya hand up .. give him a shout ..

One hot day it was aircon

The hot topic of discussions,

And the man told us, indeed, gave us an education

On nipples and Johnsons ..

Edited by THE34T
  • Like 2
Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/910/#findComment-7149638
Share on other sites

^^^ brilliant

Spotted Jezz and Rosie in Charny, at around 6. I was cammoed in the DD Focus, I saw the sneaky look you gave Maccas ;)

Hahaha ! I saw some Asian fella just standing there and was eye-balling him :P But a Frozen coke would be so good. @$4.10 for a large frozen coke is not worth it until it's 30+ :(

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/910/#findComment-7149698
Share on other sites

Was good to chat Anfanee

Finally finished the 34. and now it looks like it may spit and then dust storms. Gotta love it

Yeah. All we need when there is no rain is for someone to wash their car properly. Then it will rain.

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/910/#findComment-7151141
Share on other sites

Spotted the Trojan White StageA and what looks like Troy's old Midnight Purple 33 GTS-t (GTR wing and Rims) parked outside a house in a suburb in this town. ;)

I saw a m'nite purple 33 in Qbn yesterday, haven't seen it around before .... couldn't see details, he/she was giving it a bit and I was a pedestrian .. :ph34r:

Edited by THE34T
Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/910/#findComment-7153361
Share on other sites

white 33 leaving woden heading to tuggeres, today

silver 34 going past tuggers last night or the night before?

white 33 no front bar heading for maqurie pass (not sure how to spell it)

grey 34 on kings hwy yesterday

white 33 black rims on kings hwy yesterday

white 33 gold rims (pat?) in Calwell twice on sun/sat

black 33 gold rims again in Calwell last night spooling and fluttering like crazy - didn't go anywhere for the noise

then saw my own skyline in woden, mum took it ....

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/910/#findComment-7153795
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
    • Nah, that is hella wrong. If I do a simple linear between 150°C (0.407v) and 50°C (2.98v) I get the formula Temperature = -38.8651*voltage + 165.8181 It is perfectly correct at 50 and 150, but it is as much as 20° out in the region of 110°C, because the actual data is significantly non-linear there. It is no more than 4° out down at the lowest temperatures, but is is seriously shit almost everywhere. I cannot believe that the instruction is to do a 2 point linear fit. I would say the method I used previously would have to be better.
    • When I said "wiring diagram", I meant the car's wiring diagram. You need to understand how and when 12V appears on certain wires/terminals, when 0V is allowed to appear on certain wires/terminals (which is the difference between supply side switching, and earth side switching), for the way that the car is supposed to work without the immobiliser. Then you start looking for those voltages in the appropriate places at the appropriate times (ie, relay terminals, ECU terminals, fuel pump terminals, at different ignition switch positions, and at times such as "immediately after switching to ON" and "say, 5-10s after switching to ON". You will find that you are not getting what you need when and where you need it, and because you understand what you need and when, from working through the wiring diagram, you can then likely work out why you're not getting it. And that will lead you to the mess that has been made of the associated wires around the immobiliser. But seriously, there is no way that we will be able to find or lead you to the fault from here. You will have to do it at the car, because it will be something f**ked up, and there are a near infinite number of ways for it to be f**ked up. The wiring diagram will give you wire colours and pin numbers and so you can do continuity testing and voltage/time probing and start to work out what is right and what is wrong. I can only close my eyes and imagine a rat's nest of wiring under the dash. You can actually see and touch it.
    • So I found this: https://www.efihardware.com/temperature-sensor-voltage-calculator I didn't know what the pullup resistor is. So I thought if I used my table of known values I could estimate it by putting a value into the pullup resistor, and this should line up with the voltages I had measured. Eventually I got this table out of it by using 210ohms as the pullup resistor. 180C 0.232V - Predicted 175C 0.254V - Predicted 170C 0.278V - Predicted 165C 0.305V - Predicted 160C 0.336V - Predicted 155C 0.369V - Predicted 150C 0.407V - Predicted 145C 0.448V - Predicted 140C 0.494V - Predicted 135C 0.545V - Predicted 130C 0.603V - Predicted 125C 0.668V - Predicted 120C 0.740V - Predicted 115C 0.817V - Predicted 110C 0.914V - Predicted 105C 1.023V - Predicted 100C 1.15V 90C 1.42V - Predicted 85C 1.59V 80C 1.74V 75C 1.94V 70C 2.10V 65C 2.33V 60C 2.56V 58C 2.68V 57C 2.70V 56C 2.74V 55C 2.78V 54C 2.80V 50C 2.98V 49C 3.06V 47C 3.18V 45C 3.23V 43C 3.36V 40C 3.51V 37C 3.67V 35C 3.75V 30C 4.00V As before, the formula in HPTuners is here: https://www.hptuners.com/documentation/files/VCM-Scanner/Content/vcm_scanner/defining_a_transform.htm?Highlight=defining a transform Specifically: In my case I used 50C and 150C, given the sensor is supposedly for that. Input 1 = 2.98V Output 1 = 50C Input 2 = 0.407V Output 2 = 150C (0.407-2.98) / (150-50) -2.573/100 = -0.02573 2.98/-0.02573 + 47.045 = 50 So the corresponding formula should be: (Input / -0.02573) + 47.045 = Output.   If someone can confirm my math it'd be great. Supposedly you can pick any two pairs of the data to make this formula.
×
×
  • Create New...