Jump to content
SAU Community

Recommended Posts

I was originally under the impression that turbo choice wouldn't effect power as long as the psi its putting into the engine is the same.

For instance two turbos, 1 reaches full boost at 3000rpm. The second which is slightly bigger reaches full boost at 3500rpm. Both are putting the same psi into the same engine. Are they both going to make the same power at 6000 rpm, because both are putting in the exact same amount of boost in at that time?

Hope you understand what im getting at, and can clear it up for me.

Link to comment
https://www.sau.com.au/forums/topic/300803-power-versus-turbo-choice/
Share on other sites

I was originally under the impression that turbo choice wouldn't effect power as long as the psi its putting into the engine is the same.

For instance two turbos, 1 reaches full boost at 3000rpm. The second which is slightly bigger reaches full boost at 3500rpm. Both are putting the same psi into the same engine. Are they both going to make the same power at 6000 rpm, because both are putting in the exact same amount of boost in at that time?

Hope you understand what im getting at, and can clear it up for me.

no, think of turbos as pumps 15psi from a truck size turbo is going to pump alot more air into the engine than a small lawnmower turbo pumping 15psi

Hmmm weird, i just immediately thought that once the psi equals your set level your wastegate will open, there fore its not going to matter what your volume is.

In other words more volume into space = more pressure.

Your going to need to do a fair bit of reading. No offense.

say for example you have 2 pipes, both flowing @ 15psi. one pipe is 50mm, the other is 100mm thick. you are getting more air out of the 100mm pipe than you are out of the 50mm one.

this is the same for turbos. the bigger the turbo, the more air it will push out. a bigger turbo can produce the same flow at a lower psi than a smaller turbo can produce at its highest psi. for example, a standard r33 turbo will cause a car to produce 200kw @ 12psi because it can flow a certain amount of air at 12psi. a larger turbo, for example a gt35r can produce the same 200kw but at a lower psi (say 7psi) because it can flow the same amount of air at that psi. at 12psi on the gt35 will see you pushing out almost 300kw because it can flow much more air at 12psi.

cars run on air and spark (basically). if you have more air flowing through the motor you can produce more power. it doesnt matter what the air pressure is, its the flow of air that will effect performance (ofcorse having lots of flow and high psi will produce lots and lots of power if your car can produce enough exhaust - but thats a whole other issue.

not sure if that makes sence - but i tried lol.

say for example you have 2 pipes, both flowing @ 15psi. one pipe is 50mm, the other is 100mm thick. you are getting more air out of the 100mm pipe than you are out of the 50mm one.

this is the same for turbos. the bigger the turbo, the more air it will push out. a bigger turbo can produce the same flow at a lower psi than a smaller turbo can produce at its highest psi. for example, a standard r33 turbo will cause a car to produce 200kw @ 12psi because it can flow a certain amount of air at 12psi. a larger turbo, for example a gt35r can produce the same 200kw but at a lower psi (say 7psi) because it can flow the same amount of air at that psi. at 12psi on the gt35 will see you pushing out almost 300kw because it can flow much more air at 12psi.

cars run on air and spark (basically). if you have more air flowing through the motor you can produce more power. it doesnt matter what the air pressure is, its the flow of air that will effect performance (ofcorse having lots of flow and high psi will produce lots and lots of power if your car can produce enough exhaust - but thats a whole other issue.

not sure if that makes sence - but i tried lol.

Yeh thats a pretty good explanation. If I didnt already know that Im sure I would know that now :D Like everyone has said think of it as thought air in a pipe or water going through a pipe. A uni students definition. If you have beer bong with a straw at the bottom your going to need a lot of pressure in it to drink your bourbon in under 5 seconds. However if you had some garden hose on there the bourbon will flow into your mouth a lot faster and with a lot less pressure. Hence the idea of using a bigger hose when you have a 1L + beer bong.

Nah but seriously securitys and trents definition are good. Mine is just coz I have some spare time at work :)

I sortof agree with the above explanations, however strictly speaking I'd say the engine is the "hose" bit of that explanation - the turbo is something different. The turbo has the capacity to pump a given amount of air at a given amount of pressure, but the engine has a natural capacity to move a certain amount of air at atmospheric pressure.

Any more air than that and the engine starts providing the turbo with resistance, which is (partly) where boost comes from. Pressure also increases with heat, so if the engine is able to breathe more than a turbo can move at a given pressure - then yes, you are likely to get more power on the same boost with a bigger turbo. If the turbo is able to pump more than the engine can breathe at a given boost level however, then going to an even bigger turbo will probably not make a lot of difference...

exactly, boost comes from the turbo pumping air against the backpressure of the motor, hook a turbo up to a pipe leading into thin air and it'll flow shitloads of air but make no boost. so with bigger cams and manifolds etc you'll flow the same amount of air on less boost with the same turbo aswell. the reason bigger turbos generally make more power is because of less restriction on the exhaust side and less effort from the bigger compressor to flow the same air, hence less heat, which means less pressure. also why heat makes such a big difference for turbo cars, we use boost as a control of airflow, so the amount of air flowing at that same boost level varies depending on the air temp.

exactly, boost comes from the turbo pumping air against the backpressure of the motor, hook a turbo up to a pipe leading into thin air and it'll flow shitloads of air but make no boost. so with bigger cams and manifolds etc you'll flow the same amount of air on less boost with the same turbo aswell. the reason bigger turbos generally make more power is because of less restriction on the exhaust side and less effort from the bigger compressor to flow the same air, hence less heat, which means less pressure. also why heat makes such a big difference for turbo cars, we use boost as a control of airflow, so the amount of air flowing at that same boost level varies depending on the air temp.

That's the best explanation i've read. I used to wonder why there wouldnt be a direct correlation between airflow and boost pressure, as i had thought that the engine would provided a fixed amount of resistance against a given flowrate. The difference is that we're talking about mass flowrate not volume flowrate. The bigger turbo = less temperature at the same pressure so more mass for the same volume. Is that it?

Its not quite that easy, but as an overly simplified view of it - yes. This kind of thing is why we have compressor maps showing percentage efficiency at different flow/pressure levels. There are cases where smaller turbos have higher compressor efficiency at equivalent flow rates - this can be but isn't strictly at the higher pressure ratios/lower flow levels and could partly answer why some smaller turbos can be perceived as torquier.

Bigger compressors tend to make and hold their efficiency at higher flow rates, which is why they tend to be capable of making more power at lower boost. The turbine flow comes directly into it as well, as the easier the exhaust can leave the engine - the easier more fresh air/fuel mixture can enter the engine.

I think im slowly learning something here, keep it up and i might retain some of it.

So basically boost (psi) is more a measurement of the air that's left before the engine uses it. If the engine can use the air the boost is lower, but the flow is the same or more.

@ Lukas, Yeah i understand basic turbo info. But still a little (a lot) clueless about compressor maps.

I think im slowly learning something here, keep it up and i might retain some of it.

So basically boost (psi) is more a measurement of the air that's left before the engine uses it. If the engine can use the air the boost is lower, but the flow is the same or more.

I don't think thats quite right. 'Boost' or the PSI is a measure of the pressure in the manifold piping created by the air. The measurement is Pounds per Square Inch so at normal atmospheric pressure its applying no force, but as you compress/pressurise the air it starts pushing on the inside of the manifold and piping. Basically the reason for this is that you now have forced a higher volume of air into the space than the atmospheric pressure at whatever altitude you are at. By increasing the air pressure(therefore overall density of air) you can force more air into the engine, without having to make larger pipes or increase port size.

So by putting in a larger turbo you are able to compress more air, it might only go to the same 'PSI' but its actually filling up a larger volume with the same compression.

An easier example to understand might be a water pump, a small water pump might be able to move around or 'pressurise' a volume of say 10. If you put that into a system with 20L you would need a bigger pump to pressurise the system to the same level. So the overall PSI might be the same but you are actually moving a much larger volume of water.

I'm by no means an expert, this is just what I've gathered so if anyone thinks I'm wrong please let me know.

So by putting in a larger turbo you are able to compress more air, it might only go to the same 'PSI' but its actually filling up a larger volume with the same compression.

Careful :)

Not filling a larger volume.

The volume of the piping/plenum/cooler is always a constant.

It is the amount of air flowing at that given pressure that differs, measured in lb's/min.

One turbo will flow 40lb's/min of air @ 15psi.

The other will be 52lb's/min of air @ 15psi.

Careful :)

Not filling a larger volume.

The volume of the piping/plenum/cooler is always a constant.

It is the amount of air flowing at that given pressure that differs, measured in lb's/min.

One turbo will flow 40lb's/min of air @ 15psi.

The other will be 52lb's/min of air @ 15psi.

Good point. Am I correcting in saying that if you increase the amount of air you can compress that you could fill a larger volume at the same PSI with a larger turbo where a smaller one may struggle?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...