Jump to content
SAU Community

Recommended Posts

I've got a Black 8/1994 R32 Skyline GTS-T Type M that i'm stripping down. Damage is to the RH quarter, smaller damage to the L&R rear quarters.

Eg of parts available:

LH fog light and corner indicator

reverse lights and number plate lights

some rear lenses

full interior in gc incl trim, dash, wheel, pedals, gbox.

driveshaft

front and rear brakes

mystery suspension, has damper adjust on the front

windscreen, passenger's and rear quarter windows

undamaged left door

diff centre

NO engine, gearbox, ecu

Car is complied and has not been entered into the Written Off Vehicle Register

Just ask if there's other parts you're after and i'll have a look. Can supply pics. Located on the Gold Coast

Neil

[email protected]

0402 546 596

Link to comment
https://www.sau.com.au/forums/topic/30101-wrecking-r32-skyline-qld/
Share on other sites

  • Replies 40
  • Created
  • Last Reply

Top Posters In This Topic

inark- i thought it must have been a mistake as well but the date on the compliance plate is 8/94. is there any way of telling off the factory plate?

WazR32GTSt- the left sideskirt is untouched, but the right has a bend in it.

does every skyline owner have broken air vents? unfortunately it seems it is impossible to remove the vents without cracking them so unfortunately the only way i'll be able to sell them is the dash as a whole. maybe you guys should get in contact with someone who can do you a group deal, i think at least 5 people have contacted me wanting them :s

sLo-32- emailing you

anyone else who lives in SE Qld and wants to come have a look for bits is most welcome.

and to the person that contacted me about the mats and centre console cover, please email me, i seem to have lost your message and have photos for you.

cheers

Neil

MM2death- i do have the din slot with door. its one of the items i've had a fair bit of interest in so make an offer.

Ryno- just looked at the surround on the front bar and its got a crack through it at the top. could probably be fixed if you're interested.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...